removing front wheel bearing on chev aveo video


You are searching repair manual in PDF format about removing front wheel bearing on chev aveo video use another keyword for search another post or files



  removing front wheel bearing on chev aveo video Direct Download speed 5787 Kb/s

  removing front wheel bearing on chev aveo video Full Version speed 6767 Kb/s




1997 Ford F-250/350/Super Duty Front Wheel Grease Seal and Bearing Replacement and Repacking

0

Filed Under (Ford) by admin on 14-03-2011

download
CAUTION: Use of incompatible bearing lubricant could result in premature lubricant breakdown. The recommended wheel bearing lubricant is the lithium-base grease High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A or equivalent meeting Ford specification ESA-M1C198-A. Sodium-base grease is not compatible with lithium-base grease and should not be intermixed. Therefore, before lubricating front or rear wheel bearings (1225), thoroughly clean all old grease from the bearing and front disc brake hub and rotor (1102). If bearing adjustment does not eliminate looseness or rough and noisy operation, clean and inspect the front disc brake hub and rotor and bearings. If bearing cups or the cone and roller assemblies are worn or damaged, replace. Disassembly 1. Raise vehicle and install safety stands. 2. Remove the wheel and tire. Refer to Section 04-04 in the Body, Chassis Manual. 3. Remove the locking hubs. 4. CAUTION: Do not let the disc brake caliper (2B120) hang only by the hose, or damage might occur to the hose or disc brake caliper. Remove the disc brake caliper. Refer to Section 06-03 in the Body, Chassis manual. Securely wire the disc brake caliper to the frame. 5. For vehicles equipped with automatic locking hubs, remove C-ring or snap ring and three-piece thrust washers (spacers). Remove the cam assembly and wheel bearing nut retaining key. Remove wheel bearing retainer (nut) using Hub Nut Wrench T95T-1197-B. Repack the wheel bearings with the specified lubricant (grease). For vehicles with manual locking hubs, remove snap ring, three-piece thrust washers (spacers), the outer lock nut, lockwasher, and inner lock nut using Spanner Locknut Wrench D85T- 1197-A or equivalent. 6. Remove the front disc brake hub and rotor. The front outer wheel bearing will slide out as the hub is removed. 7. Remove the retaining nuts of the front wheel spindle (3105). Carefully remove the front wheel spindle from the knuckle studs and halfshaft (3A329). If necessary, lightly tap the end of the spindle with a rawhide hammer to remove. 8. Clean old grease from the needle bearings and the bore seal of the front wheel spindle. To replace spindle bearing or inner seal, refer to Section 05-03A or Section 05-03B. 9. Clean any old grease or dirt from these parts and replace if signs of excessive wear are noted. Assembly 1. Using High-Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A or equivalent meeting Ford specification ESA-M1C198-A, thoroughly lubricate the needle bearing and coat the front wheel spindles or face that mates with the seals of the front wheel spindle. 2. Assemble the front wheel spindle over the halfshaft onto the knuckle studs. Tighten the retaining nuts to 68-81 Nm (50-60 lb-ft). 3. Remove the front inner wheel bearing, wheel hub grease seal (1190) from the front disc brake hub and rotor using Bearing Cup Puller T77F-1102-A and Impact Slide Hammer T50T-100-A. Inspect bearings and replace as necessary. 4. Inspect the bearing cups for pits or cracks. If necessary, remove with a drift. If new cups are installed, install new cones and rollers. 5. Lubricate the bearings with High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A or equivalent meeting Ford Specification ESA-M1C198-A. Clean all old grease from the front disc brake hub and rotor. Pack the cones and rollers. If a bearing packer is not available, work as much lubricant as possible between the rollers and the cages. 6. Position the front inner wheel bearing in the inner cup and install the new wheel hub grease seal using a hammer, Driver Handle T80T-4000-W and the proper seal installer.

Related entry:

2001 4wd tacoma wheel bearing service, car repair for 2001grand marquis front wheel bearings, 99 landcruiser front wheel bearings drawing, 2001 ford escape wheel bearing replacement, 2003 envoy front wheel bearing axle nut torque, specs front end hub 2003 chev venture, 2004 mercedes vito 111 tdi van rear w bearings removal, carrier bearing for a 2003 alero coupe, 2005 toyota tacoma front axle diagram, bering hyundai elantra 2002,

1997 Ford Aerostar/Ranger Wheel Grease Seal and Bearing Front Replacement and Repacking

0

Filed Under (Ford) by admin on 02-02-2011

download
The recommended wheel bearing lubricant is lithium-base High-Temperature Constant Velocity Joint Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. CAUTION: Sodium-base grease is not compatible with lithium-base grease. Do not intermix. Clean all old lubricant grease prior to lubricating front/rear wheel bearing. Use of incompatible bearing lubricant could result in premature lubricant breakdown. NOTE: If bearing adjustment does not eliminate looseness or rough and noisy operation, clean, inspect and repack the hub and wheel bearings with specified wheel grease. If wheel bearing cup or the cone and roller assemblies are worn or damaged, they should be replaced. Manual Locking Hub, Ranger Disassembly 1. Raise the vehicle and install Rotunda Car/Truck Stands 077-00018 or equivalent. 2. Remove the wheel and tire assembly. 3. Remove the retainer washers and remove the hub assembly. Refer to Manual Locking or Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for removal. 4. Remove the disc brake caliper (2B120) as described in Section 06-03. 5. Remove the hub and rotor. Remove the outer wheel bearing cone. 6. Remove the wheel hub grease seal (1190) from the rotor with Seal Remover TOOL-1175-AC or equivalent and Impact Slide Hammer T50T-100-A. Discard wheel hub grease seal and replace upon assembly. 7. Remove excluder seal. 8. Remove the inner wheel bearing. 9. NOTE: If new wheel bearing cups are installed, install new cone and roller assemblies. Inspect the wheel bearing cups for pits or cracks. If necessary, remove them with Internal Puller D80L-943-A or equivalent and Impact Slide Hammer T50T-100- A. Assembly 1. Lubricate the wheel bearings with High Temperature Constant Velocity Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. Clean all grease from the hub. Pack the cones and rollers. If a bearing packer is not available, work as much lubricant as possible between the rollers and the cages. 2. If wheel bearing cups are to be installed, position wheel bearing cups in rotor and drive in place with Bearing Cup Replacer T80T-4000-P and Driver Handle T80T-4000-W. 3. Position excluder seal on spindle and drive into position using Spindle Seal Replacer T95T-3132-D. 4. Position the inner wheel bearing in the inner wheel bearing cup in the rotor. Install the wheel hub grease seal by driving in place with Seal Replacer T80T-4000-T and Driver Handle T80T-4000-W. 5. Carefully install the rotor onto the front wheel spindle (3105). Refer to Section 06-03. 6. Install outer wheel bearing into rotor. 7. Refer to Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for remainder of installation.

Related entry:

1991 f-150 four wheel drive front wheel bearings, how to remove disc brake rotor 1993 Ford Ranger 4 wheel drive automatic hubs, honda accord 1995 hub diagram, how toemove grease cap on front axle ford2005 e405, how to install hub bearing 2006 bmw x5, frame specifications for 1996 ford ranger 2 wheel drive, ford festiva front wheel assembly, Ford festiva front disk assembly, dust cap for 2006 ford e350 tool, can you grease a wheel hub assembly on a 2003 cadillac escalade,

2004 Ford F-150 Rear Axle Differential Cover Axle Shaft Oil Seal and Rear Wheel Bearing REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 28-02-2011

download
1. With the vehicle in NEUTRAL, position on a hoist. For additional information, refer to Section 100-00. 2. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-00. 3. Remove the parts in the order indicated in the following illustration and table. 4. To install, reverse the removal procedure. 5. Fill the axle with the specified quantity of the specified lubricant. For additional information, refer to the Specifications in this section. Item 2: Rear Disc Brake Caliper Removal Note 1. CAUTION: Do not allow the caliper to hang from the brake hose. Provide a suitable support. Position the rear disc brake caliper aside. For additional information, refer to Section 206-00. Item 7: Differential Pinion Shaft Removal Note 1. Move the differential pinion shaft out far enough to remove the U-washers. Replace the shaft and install the lock bolt finger tight when U-washers are removed. Item 8: U-washer Removal Note 1. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers. 1. Push the axle shafts inboard. 2. Remove the U-washers. Item 10 and 11: Wheel Bearing Oil Seal and Axle Shaft Bearing Removal Note 1. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 8.8 inch rear axle, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. 2. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 9.75 inch and the 10.25 inch rear axles, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. Item 11: Axle Shaft Bearing Installation Note 1. For the 8.8 inch and the 9.75 inch rear axles, use the special tools to install the rear axle wheel bearing. 2. For the 10.25 inch rear axle, use the special tools shown to install the rear axle wheel bearing. Item 10: Wheel Bearing Oil Seal Installation Note 1. Use the special tools shown to install the rear wheel bearing oil seal. Item 8: U-washer Installation Note 1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers. 1. Position the two U-washers on the button end of the axle shafts. 2. Pull the axle shafts outward.

Related entry:

2004 ford explorer rear differential diagram, how to remove rear axle shaft of mitsubishi strada triton, 2006 suzuki forenza front wheel drive axle diagram, saturn wheel hub torque specs, balance shaft seal for 2004 honda acccord 4 cylinder schematic, 2004 expedition right axle tube seals, 2005 kia sorento drive mid shaft bearing replacement procedure, camry rear hub removeal, how to install rear brakes on a lt80, 2003 vibe awd rear differential replacement,

2000- 2005 Lincoln Aviator, Ford Explorer, Exp Sport, Exp Sport-Trac, Mercury Mountaineer Wheel Bearings REMOVAL & INSTALLATION ?

0

Filed Under (Lincoln) by admin on 11-01-2011

download
Removal & Installation WARNING Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied. NOTE Have an assistant press the brake pedal to keep the axle from turning. 1. Before servicing the vehicle, please familiarize yourself with safety procedures. ? Remove the axle-to-wheel hub retainer nut and washer. ? Remove the parking brake shoes. WARNING Do not use a hammer to separate the outboard CV-joint from the hub. Damage to the threads and internal CV-joint components can result. 2. 3. ? Press the outboard CV-joint until it is loose from the hub. ? Remove and discard the toe link-to-wheel knuckle nut. WARNING Do not damage the boot while separating the toe link from the wheel knuckle. 4. 5. ? Remove the bolt and separate the toe link from the wheel knuckle. ? Remove and discard the upper arm-to-wheel knuckle nut. WARNING Do not damage the boot while separating the ball joint from the wheel knuckle. 6. 7. ? Remove the bolt and separate the upper arm from the wheel knuckle. ? Remove and discard the lower arm-to-wheel knuckle nut. 8. 9. ? Remove the lower arm-to-wheel knuckle bolt. ? Remove the wheel knuckle. ? Using a suitable press, remove and discard the wheel hub. ? Remove and discard the wheel bearing retainer ring. ? Using a suitable press, remove the wheel bearing. 10. 11. 12. 13. 14. Fig. Rear hub/bearing Assembly-Aviator, Explorer and Mountaineer Fig. Pressing out the bearing ? To install: 1. Installation is the reverse of the removal procedure. ? Observe the following torques: 2. Lower arm-to-wheel knuckle nut: 111 ft. lbs. (150 Nm). ? Upper arm-to-wheel knuckle nut: 66 ft. lbs. (90 Nm). ? Toe link-to-wheel knuckle nut: 66 ft. lbs. (90 Nm). ? Axle-to-hub retainer nut: 203 ft. lbs. (275 Nm). ? ? Always install a new: 3. Axle-to-wheel hub retainer nut. ? Toe link-to-wheel knuckle nut. ? Upper arm-to-wheel knuckle nut. ? Lower arm-to-wheel knuckle nut. ? Wheel hub. ? Wheel bearing retainer ring. ? ? 1. Before servicing the vehicle, refer to the precautions in the beginning of this section. ? Remove or disconnect the following: NOTE Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied. 2. NOTE Do not use a hammer to separate the outboard CV joint from the hub. Damage to the threads and internal CV joint components may result.

Related entry:

2007 chevy aveo wheel bearing torque, 2004 mercury mountaineer axle nut, Torque wrench AXLE NUT 2001 Oldsmobile Intrigue, how to repack bearings on hummer h3, how to repair a rear wheel bearing on a daewoo matiz, How to replace four-wheel-drive switch on a Dinali, 94 ford explorer manuel hubs wheel barrings diagrams, 2002 e150 bearing nut torque specs, rx330 wheel bearing torque specifications, 2003 rendezvous front hub bolts torque,

1996 Ford Aerostar Front Wheel Bearing ADJUSTMENTS

0

Filed Under (Ford) by admin on 28-02-2011

download
Manual Locking Hubs, Ranger 1. Raise the vehicle and install safety stands. 2. Remove the lug nuts (1012) and wheel and tire assembly. Refer to Section 04-04. 3. Remove the retainer washers from the wheel hub bolt nut studs and the manual locking hub assembly from the front wheel spindle (3105). 4. Remove the snap ring from the end of the shaft of the front wheel spindle. Manual Locking Hub, Exploded View, Ranger 5. Remove the axle shaft spacers. 6. Remove the outer wheel bearing locknut from the front wheel spindlej using Hub Locknut Wrench Prong T83T-1197-B. Engage tool tabs into locknut slots. 7. Remove locknut washer from front wheel spindle. 8. Loosen the inner wheel bearing locknut. Engage tool tab in locknut slots. Make sure tool is centered over the locknut pin. 9. Tighten the inner locknut to 47 Nm (35 lb-ft) while turning the rotor in the opposite direction to seat wheel bearings. 10. NOTE: If necessary, tighten inner locknut slightly to align the locknut pin with lockwasher hole. Spin the rotor and back off the inner locknut one-quarter turn. Retighten the inner locknut to 1.8 Nm (16 lb-in). 11. Install the lockwasher on the front wheel spindle. 12. Install the outer wheel bearing locknut using locknut wrench. Tighten locknut to 203 Nm (150 lb-ft). 13. Check the end play of the wheel and tire assembly on the front wheel spindle. Final end play should be 0.00-0.08mm (0.000-0.003 inch). The maximum torque to rotate the hub is 2.8 Nm (25 lb-in). 14. Install the axle shaft spacer. 15. Clip the snap ring onto the end of the shaft of the front wheel spindle. 16. Install the manual hub assembly over the front wheel spindle. Install the retainer washers. 17. Install the wheel and tire assembly. Install and tighten lug nuts to 135 Nm (100 lb-ft). Automatic Locking Hubs, Ranger 1. Raise the vehicle and install safety stands. 2. Remove the lug nuts and the wheel and tire assembly. Refer to Section 04-04. 3. Remove the retainer washers from the wheel hub bolt nut studs. Remove the automatic locking hub assembly from the front wheel spindle. Automatic Locking Hub, Exploded View, Ranger

Related entry:

how much do you tighten rear hub nuts on a 1977 f-350,