replacing a master cylinder on k1500


You are searching repair manual in PDF format about replacing a master cylinder on k1500 use another keyword for search another post or files



  replacing a master cylinder on k1500 Direct Download speed 5787 Kb/s

  replacing a master cylinder on k1500 Full Version speed 6767 Kb/s




2000 Ford F-Super Duty 250-550 Clutch Master Cylinder and Reservoir REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 08-03-2011

download
Removal CAUTION: Remove the entire clutch hydraulic system from the vehicle as an assembly when installing a new clutch master cylinder assembly (7C522). 1. Disconnect the clutch hydraulic tube from the dash clip. 2. Raise and support the vehicle. For additional information, refer to Section 100-02. 3. Unlock and remove the slave cylinder (7A564) from the transmission. Compress and twist the slave cylinder to unlock it from the transmission. 4. Disconnect the clutch hydraulic tube from the floor pan clip. Position the slave cylinder and hydraulic tube forward below the left engine bank. This will make it easier to unlock the clutch master cylinder from the clutch pedal and support bracket (7B633) by reducing tension on the hydraulic tube. 5. Lower the vehicle. 6. WARNING: The clutch pedal is under spring tension. Unlock the push rod bushing retaining clips and separate the clutch master cylinder push rod from the clutch pedal. 7. Remove and discard the push rod bushing (7526). 8. Remove the switch cover, and remove the clutch pedal position switch (7C534) from the clutch master cylinder push rod. 9. Separate the power distribution box from the bracket to gain access to the clutch master cylinder. 10. Unlock and remove the clutch master cylinder from the clutch pedal and support bracket. Compress and twist the clutch master cylinder clockwise 45 degrees to unlock it from the clutch pedal and support bracket. 11. Remove the clutch hydraulic reservoir from the wiring tray and separate the clutch hydraulic tube from the brake master cylinder assembly. Position the clutch hydraulic reservoir aside. 12. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, wash the surface with water immediately. Remove the clutch hydraulic system from the vehicle. 13. Clean the clutch hydraulic system components to prevent contaminants from entering the hydraulic system. 14. CAUTION: Place a suitable container under the clutch master cylinder. Disconnect the hydraulic tube from the clutch master cylinder. 1. Using a 3/32-inch punch and a hammer, drive out the roll pin, and discard it. 2. Disconnect the hydraulic tube from the clutch master cylinder.

Related entry:

1984 F350 Clutch Cable Install, 2008 Masda b2300 transmisson clutch slave clylinder how to bleed system, 2000 ford f750 clutch slave cylinder, ports where centric master cylinder for chevy, how to replace clutch master cylinder on 06 jetta, how to replace clutch slave cylinder on a 650 ford, how to replace clutch slave cylinder on a 650 ford truck, location of bleeder on 1990 f250 manual transmission, micra cr10 bleeding clutch, on a 1998 cavalierz24 how do you remove the master cylnder assembly,

2001 Ford F-150 Clutch Master Cylinder/ Reservoir REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 08-03-2011

download
Removal NOTE: When replacing clutch master cylinder (7A543), remove tubing from vehicle for bench bleeding procedure. 1. Disconnect the clutch master cylinder push rod from the clutch and brake pedal pivot shaft lever. 2. Disconnect the clutch pedal position switch (CPP) (11A152). 3. Remove the pushpins. 4. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking, or towing an air suspension vehicle. This can be accomplished by turning off the rh kick panel area. Failure to inflation of deflation of the air springs which may result in shifting of the vehicle during these operations. Raise and support the vehicle. For additional information, refer to Section 100-02. 5. Disconnect the clutch hydraulic line from the slave cylinder. 6. Lower the vehicle. 7. Remove the clutch master cylinder reservoir and clutch master cylinder. Rotate the clutch master cylinder 45 degrees clockwise. 8. CAUTION: Clean all rubber clutch master cylinder parts with Ford High Performance DOT 3 Motor Vehicle Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A. Removal NOTE: When replacing clutch master cylinder (7A543), remove tubing from vehicle for bench bleeding procedure. 1. Disconnect the clutch master cylinder push rod from the clutch and brake pedal pivot shaft lever. 2. Disconnect the clutch pedal position switch (CPP) (11A152). 3. Remove the pushpins. 4. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking, or towing an air suspension vehicle. This can be accomplished by turning off the rh kick panel area. Failure to inflation of deflation of the air springs which may result in shifting of the vehicle during these operations. Raise and support the vehicle. For additional information, refer to Section 100-02. 5. Disconnect the clutch hydraulic line from the slave cylinder. 6. Lower the vehicle. 7. Remove the clutch master cylinder reservoir and clutch master cylinder. Rotate the clutch master cylinder 45 degrees clockwise. 8. CAUTION: Clean all rubber clutch master cylinder parts with Ford High Performance DOT 3 Motor Vehicle Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.

Related entry:

2001 ford F-650 clutch master cylinder, 2005 ford escape torque on cyclinder head bolts 3 0 litre engine, cylinder layout in ford five hundred, diagram of key cylinder ford f250 1990,

FORD LIGHT TRUCK: 1993 AEROSTAR, BRONCO, EXPLORER, F-150-350 SERIES, F-47, RANGER UNRESPONSIVE CLUTCH: AIR ENTRAPPED IN HYDRAULIC SYS

0

Filed Under (Ford) by admin on 07-01-2011

download
ISSUE A “soft” unresponsive clutch pedal may be felt or the driver may be unable to release the clutch. This is caused by air entrapped in the clutch hydraulic system. ACTION Use the information in this TSB article in addition to the appropriate bleeding procedure. This article includes detail as well as extra service tips for easier hydraulic clutch bleeding. The clutch hydraulic system for the 1993 model year is new and more difficult to bleed than the previous hydraulic system. Therefore, a different bleeding procedure is required for these vehicles. RANGER, EXPLORER, AEROSTAR The most difficult systems to bleed are on the Ranger, Explorer, Aerostars. NOTE: When installing dry clutch cylinder or tube service parts, do the bench bleed procedure first. BENCH BLEED The compact vehicles are more difficult to bleed because the downward angle of the master cylinder makes it difficult for air to escape up into the reservoir. Therefore, if the master cylinder is removed from the vehicle and bled while held in a vertical orientation (a bench bleed) air can escape much more efficiently. Refer to Fig. 1 . BENCH BLEEDING PROCEDURE (CONCENTRIC SLAVE CYLINDER) 1. Remove master cylinder, line and reservoir from vehicle and assemble with replacement parts required based on initial concern. 2. Hold the master cylinder vertically with the reservoir feed hose in the highest position on the body. See Fig. 1 . 3. Fill the reservoir and extend above the master cylinder and assure the quick connect on the clutch line is below the master cylinder. (Lightly clamp reservoir in a vise). 4. Using a small screwdriver, depress the internal mechanism of the male quick connect coupling to open the valve. See Fig. 1 . 5. Stroke and hold master cylinder pushrod. 6. Close quick connect valve. 7. Release master cylinder pushrod. 8. Fill reservoir. 9. Repeat Steps 4 through 8 four more times. 10. With the master cylinder still being held with the outlet tube and reservoir feed tube ends high, quick connect closed and the reservoir full, proceed as follows: a. Push the pushrod into the body several times quickly to expel any remaining air. b. If it is a remote reservoir, pinch the supply hose with your fingers two or three times to help move air into reservoir. 11. When the movement of the pushrod is .130″ (4mm) or less when stroked in Step 10, reinstall the master cylinder into the vehicle and couple it to the slave cylinder.

1998 Ford Expedition Master Cylinder Bleeding PROCEDURES

0

Filed Under (Ford) by admin on 28-03-2011

download
Master Cylinder, In Vehicle WARNING: Brake fluid contains polyglycol ethers and polyglycols. Avoid contact with eyes. Wash hands thoroughly after handling. If brake fluid contacts eyes, flush eyes with running water for 15 minutes. Get medical attention if irritation persists. If taken internally, drink water and induce vomiting. Get medical attention immediately. CAUTION: Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. NOTE: When any part of the hydraulic system has been disconnected for repair or new installation, air may get into the system and cause spongy brake pedal action. This requires bleeding of the hydraulic system after it has been correctly connected. The hydraulic system can be bled manually or with pressure bleeding equipment. 1. NOTE: When a new brake master cylinder has been installed or the system has been emptied, or partially emptied, it should be primed to prevent air from getting into the system. Disconnect the brake master cylinder outlet tubes. 2. Install short brake tubes with ends submerged in the brake master cylinder reservoir and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ- 19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A. 3. Have an assistant pump the brake pedal until clear fluid flows from both brake tubes without air bubbles. 4. Remove the short brake tubes and install the brake outlet tubes. 5. Bleed each brake tube at the brake master cylinder as follows: 1. Have an assistant pump the brake pedal and then hold firm pressure on the brake pedal. 2. Loosen the rearmost brake tube fittings until a stream of brake fluid comes out. Have an assistant maintain pressure on the brake pedal while tightening the brake tube fitting. 3. Repeat this operation until clear, bubble-free fluid comes out. 4. Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube. 6. While the assistant maintains pressure on the brake pedal, tighten the brake tubes.

Related entry:

how to install rubbers in a brake master cylinder, Mitsubishi Nativa 1998 break parts,

1994 Buick Park Avenue MASTER CYLINDER REPLACEMENT

0

Filed Under (Buick) by admin on 15-12-2010

download
REMOVE OR DISCONNECT 1. Retainer and electrical connector from fluid level sensor. 2. Drain brake fluid front mister cylinder reservoir. 3. Reservoir hose from master cylinder. Plug hose to prevent fluid loss and contamination. 4. Brake pipes from master cylinder. Plug open pipes to prevent fluid loss and contamination. 5. Two attaching nuts. 6. Master cylinder. 7. Reservoir, if it is to he used on replacement master cylinder. INSTALL OR CONNECT Reservoir onto master cylinder, as needed. Master cylinder on to power booster. Attaching nuts. Tighten to 27 Nm (20 lb. ft.). Brake pipes. Tighten brake pipe fittings to 15 Nm (11 lb. ft.). Reservoir hose onto master cylinder. Fill master cylinder reservoir to full level mark using only Delco Supreme 11 Brake Fluid, or equivalent DOT 3 brake fluid. 7. Electrical connector to fluid level sensor, secure with retainer. 8. Bleed hydraulic system. 9. Recheck fluid level in reservoir. 1. 2. 3. 4. 5. 6.