rover 25 clutch diagram


You are searching repair manual in PDF format about rover 25 clutch diagram use another keyword for search another post or files



  rover 25 clutch diagram Direct Download speed 5787 Kb/s

  rover 25 clutch diagram Full Version speed 6767 Kb/s




2005–2006 Toyota Tacoma CLUTCH PEDAL SQUEAK NOISE

0

Filed Under (Toyota) by admin on 04-06-2011

download
Some customers may complain about a “squeak” or “creak” noise when depressing or releasing the clutch pedal. The clutch master cylinder clevis assembly has been improved to eliminate this condition. Repair Procedure 1. Record all radio presets before starting. 2. Disconnect the negative (–) battery terminal cable. 3. Remove the clutch pedal sub–assembly. A. Remove the front door opening trim LH (scuff plate). B. Remove the cowl side trim board. C. Remove the instrument panel finish panel lower No. 1. D. Remove the driver’s side Junction Block. E. Remove the turnover (compression) spring. F. Remove the bolt attached to the instrument panel reinforcement assembly. G. Remove the clutch pedal sub–assembly. a. Remove the bolt and nut. b. Remove the clutch pedal from the clutch pedal support. 4. Remove the clutch pedal spring holder from the clutch pedal support. 5. Remove the clutch pedal pad. 6. Remove the two (2) clutch pedal bushes from the clutch pedal. 7. Remove the clutch pedal shaft collar. 8. Using needle–nose pliers, remove the No. 1 cushion from the clutch pedal. 9. Install the clutch pedal No. 1 cushion on the NEW clutch pedal sub–assembly. NOTE: Install parts on the NEW clutch pedal sub–assembly BEFORE installing in the vehicle. 10. Install the clutch pedal shaft collar. A. Apply MP grease to the clutch pedal shaft collar. B. Install the clutch pedal shaft collar onto the clutch pedal. 11. Install the clutch pedal bushes. A. Apply MP grease to the two (2) NEW bushes. B. Install the two (2) bushes onto the clutch pedal. 12. Install the clutch pedal pad. 13. Install the clutch pedal spring holder. A. Apply MP grease to the contact surface of the clutch pedal spring holder. B. Install the clutch pedal spring holder. 14. Remove the clevis sub–assembly. A. Measure length “A” of the clutch master cylinder. a. Measure length “A” between the lock nut and the thread end with a ruler. b. Record length “A”. B. Remove the clevis sub–assembly from the master cylinder. a. Loosen the lock nut. b. Rotate and remove the clevis sub–assembly. 15. Install the NEW clevis sub–assembly. A. Rotate the lock nut to match length “A”. B. Rotate and install the NEW clevis sub–assembly to contact the lock nut. C. Tighten the lock nut and torque to specification. Torque: 11.8 NSm (120 kgfScm, 8.7 ftSlbf) D. Apply MP grease to the ball end of the clevis sub–assembly where it will contact the clutch pedal. 16. Install the NEW clutch pedal sub–assembly. A. Install the clutch pedal onto the clutch support with the bolt and nut. Torque: 34 NSm (347 kgfScm, 25 ftSlbf) HINT: Install the bolt from the left side of the vehicle. B. Apply MP grease to the clutch pedal sub–assembly where the clevis sub–assembly contacts the clutch pedal. NOTE: Failure to apply grease to the clevis and clutch pedal sub–assemblies could cause the noise to return. C. Tighten the bolt to the instrument panel reinforcement assembly. Torque: 8 NSm (82 kgfScm, 6 ftSlbf) 17. Install the turnover (compression) spring. A. Apply MP grease to the contact surface of the spring holder, clutch pedal, and spring. B. Install the spring onto the clutch pedal and spring holder.

Related entry:

Hyundai Tiburon Clutch Replacement Instructions, Magnetic clutch relay for 2010 Toyota Tacoma, kia sedona clutch adjustment, rover45clutch bleeding, how to remove clutch for air condition for chev truck, F350A/C clutch repair how to repair, how to replace a 1999 toyota celica clutch, how to replace clutch 2000 beetle, how to change clutch plates in 2006 kia, 2004 mazda 6 clutch replace tutorial,

2000 Ford F-Super Duty 250-550 Clutch Master Cylinder and Reservoir REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 08-03-2011

download
Removal CAUTION: Remove the entire clutch hydraulic system from the vehicle as an assembly when installing a new clutch master cylinder assembly (7C522). 1. Disconnect the clutch hydraulic tube from the dash clip. 2. Raise and support the vehicle. For additional information, refer to Section 100-02. 3. Unlock and remove the slave cylinder (7A564) from the transmission. Compress and twist the slave cylinder to unlock it from the transmission. 4. Disconnect the clutch hydraulic tube from the floor pan clip. Position the slave cylinder and hydraulic tube forward below the left engine bank. This will make it easier to unlock the clutch master cylinder from the clutch pedal and support bracket (7B633) by reducing tension on the hydraulic tube. 5. Lower the vehicle. 6. WARNING: The clutch pedal is under spring tension. Unlock the push rod bushing retaining clips and separate the clutch master cylinder push rod from the clutch pedal. 7. Remove and discard the push rod bushing (7526). 8. Remove the switch cover, and remove the clutch pedal position switch (7C534) from the clutch master cylinder push rod. 9. Separate the power distribution box from the bracket to gain access to the clutch master cylinder. 10. Unlock and remove the clutch master cylinder from the clutch pedal and support bracket. Compress and twist the clutch master cylinder clockwise 45 degrees to unlock it from the clutch pedal and support bracket. 11. Remove the clutch hydraulic reservoir from the wiring tray and separate the clutch hydraulic tube from the brake master cylinder assembly. Position the clutch hydraulic reservoir aside. 12. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, wash the surface with water immediately. Remove the clutch hydraulic system from the vehicle. 13. Clean the clutch hydraulic system components to prevent contaminants from entering the hydraulic system. 14. CAUTION: Place a suitable container under the clutch master cylinder. Disconnect the hydraulic tube from the clutch master cylinder. 1. Using a 3/32-inch punch and a hammer, drive out the roll pin, and discard it. 2. Disconnect the hydraulic tube from the clutch master cylinder.

Related entry:

saturn vue clutch removal, dodge d150 master cylinder fill level, bleeding clutch slave cylinder 03 cavalier, 04 CAVALIER SLAVE CYL DIAGRAM, how to remove bolt on clutch lifter arm peugeot 806, how to install master cilinder in chavrolet silverado, how to fix cutlass supreme master cylinder, how to efficiently bleed clutch on a 98 ford explorer, how to change a master brake cylinder izuzu npr, how to replace a slave cylinder 2002 chevy cavalier,

Airbag diagnostics – Rover Metro • Rover 100 • New Rover 400 • Rover 600

0

Filed Under (Rover) by admin on 23-05-2010

download
some models, no serial diagnostics are available with the airbag system. On these systems, faults are reported by means of the Airbag warning light on the dashboard. The Rover models concerned are as follows: • Metro • Rover 100 • New Rover 400 • Rover 600
ED3 Airbag For the ED3 system on Metro, Rover 100, and New Rover 400 vehicles, the airbag warning light has the following meaning.
Warning light behavior when Meaning ignition is switched on. Comes on then goes off after No fault in system 3 seconds. Comes on and stays on Fault in airbag module, SRS ECU, cabling, or airbag module connector Comes on, goes off after 3 Fault in airbag module, SRS seconds, then comes back on ECU, cabling, or airbag and remains on. module connector

Related entry:

alternator belt rover 400, rover 620 wurkshop manual free pdf dawnload, ecu pinout rover 600, geo metro remove airbag, 2002 Rover 25-workshop manual-free download, Rover 25 Manual Free Download, User manual for 2002 Rover 25 series,

2001 Ford F-150 Clutch Master Cylinder/ Reservoir REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 08-03-2011

download
Removal NOTE: When replacing clutch master cylinder (7A543), remove tubing from vehicle for bench bleeding procedure. 1. Disconnect the clutch master cylinder push rod from the clutch and brake pedal pivot shaft lever. 2. Disconnect the clutch pedal position switch (CPP) (11A152). 3. Remove the pushpins. 4. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking, or towing an air suspension vehicle. This can be accomplished by turning off the rh kick panel area. Failure to inflation of deflation of the air springs which may result in shifting of the vehicle during these operations. Raise and support the vehicle. For additional information, refer to Section 100-02. 5. Disconnect the clutch hydraulic line from the slave cylinder. 6. Lower the vehicle. 7. Remove the clutch master cylinder reservoir and clutch master cylinder. Rotate the clutch master cylinder 45 degrees clockwise. 8. CAUTION: Clean all rubber clutch master cylinder parts with Ford High Performance DOT 3 Motor Vehicle Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A. Removal NOTE: When replacing clutch master cylinder (7A543), remove tubing from vehicle for bench bleeding procedure. 1. Disconnect the clutch master cylinder push rod from the clutch and brake pedal pivot shaft lever. 2. Disconnect the clutch pedal position switch (CPP) (11A152). 3. Remove the pushpins. 4. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking, or towing an air suspension vehicle. This can be accomplished by turning off the rh kick panel area. Failure to inflation of deflation of the air springs which may result in shifting of the vehicle during these operations. Raise and support the vehicle. For additional information, refer to Section 100-02. 5. Disconnect the clutch hydraulic line from the slave cylinder. 6. Lower the vehicle. 7. Remove the clutch master cylinder reservoir and clutch master cylinder. Rotate the clutch master cylinder 45 degrees clockwise. 8. CAUTION: Clean all rubber clutch master cylinder parts with Ford High Performance DOT 3 Motor Vehicle Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.

Related entry:

07 silverado master cylinder diagram, crankshaft pulley for 1999 ford f-150, diagram of eldorado brake fluid distribution, HOW TO CODE A FORD TRANSIT LOCK CYLINDER FOR DOOR,

Diagnostic connector location – Rover / MG

0

Filed Under (Rover) by admin on 20-06-2010

download
Rover 100 16 pin CAN1 In fuse compartment Rover 200 16 pin CAN1 Behind central console, on end of a free cable. Rover 200 3 pin – Engine MEMS In engine bay beside ECU Rover 200 3 pin – Security A0903111-1 Rear of engine bay New Rover 200 16 pin CAN1 Drivers side, On side of central column. Rover 400 16 pin CAN1 Above pedals, on the end of a free cable. Rover 400 3 pin – Engine A0903111-1 In engine bay beside ECU Rover 400 3 pin – Security A0903111-1 Rear of engine bay New Rover 400 16 pin CAN1 Drivers side, On side of central column. Rover 600 16 pin CAN1 In front of drivers seat above pedals Rover 600 Honda PGM-Fi Honda PGM-Fi Passenger footwell, behind triangular panel just in front of door hinge. Rover 800 16 pin CAN1 Drivers side of central column Rover 800 3 pin – Engine MEMS In engine bay beside ECU Rover 800 4 pin – Security A0903111-1 Bottom of dash, below steering wheel. Rover 25 16 pin CAN1 Drivers side, On side of central column.

Related entry:

2001 land rover freelander 2 1l engine, Repair manual Land Rover Freelander 2001 2 5 V6, rover 100 3pin adapter, thermostat housing on a rover 400 ser 1999, where is the thermostat housing on a rover 400 ser 1999,