s10 1992


You are searching repair manual in PDF format about s10 1992 use another keyword for search another post or files



  s10 1992 Direct Download speed 5787 Kb/s

  s10 1992 Full Version speed 6767 Kb/s




1992 Chevy S10/T10 P/U Engine Cranks But Will Not Run

0

Filed Under (Chevrolet) by admin on 26-08-2010

download
CIRCUIT DESCRIPTION This chart assumes that the battery condition and engine cranking speed are OK, and there is adequate fuel the tank. This chart should be used on engines using the Model 700 throttle body. TEST DESCRIPTION Number(s) below refer to circled number(s) on the diagnostic chart: 1. A “Service Engine Soon” light “ON” is a basic test to determine if there is a 12 volt supply and ignition 12 volts to ECM. No ALDL may be due to an ECM problem and CHART A-2 will diagnose the ECM. If TPS is over 2.5 volts the engine may be in the clear flood mode which will cause starting problems. If coolant sensor is below -30° C, the ECM will provide fuel for this extremely cold temperature which will severely flood the engine. 2. Voltage at the spark plug is checked using spark tester tool ST-125 (J 26792) or equivalent. No spark indicates a basic ignition problem. 3. While cranking engine there should be no fuel spray with injector disconnected. Replace an injector if it sprays fuel or drips like a leaking water faucet. 4. Use an injector test light like J 34730, BT-8329A or equivalent, to test injector circuit. A blinking light indicates the ECM is controlling the injector. 5. This test will determine if there is fuel pressure at the injector and that the injector is operating. DIAGNOSTIC AIDS If no trouble is found in the fuel pump circuit or ignition system and the cause of a “Engine Cranks But Will Not Run” has not been found, check for:

1993 Dodge Dakota FUSE PANEL IDENTIFICATION (1992-95 MODELS)

0

Filed Under (Dodge) by admin on 26-05-2010

download
Fig. 1: Fuse Block Identification (1992-95 Models) Courtesy of CHRYSLER CORP. FUSE & CIRCUIT BREAKER I.D. (UNDER INSTRUMENT PANEL) 1 – 30 Amp (Green) A/C Or Heater Blower Motor. 2 – 30 Amp (Circuit Breaker) Power Windows. 3 – 10 Amp (Red) (1992-93); 15 Amp (Lt Blue) (1994-95) Back-Up Lights, A/C Electronic Cycling Switch (1992-93); Back-Up Lights, Airbag Module, Overhead Console (1994-95). 4 – Not Used (1992); 5 Amp (Tan) (1993-95) ABS Brake System. 5 – 20 Amp (Yellow) Power Door Locks. 6 – 15 Amp (Lt. Blue) Horn, Tachometer. 7 – 10 Amp (Red) Anti-Lock Brake Module, Stoplights, Buzzers. 8 – 20 Amp (Yellow) Taillights, Park, Side Marker Lights, Clock & Radio Display Intensity, License & Panel Lights.

Related entry:

ford capri convertable repair manuel free download, ford capri convertable repair nanual free download, 1992 camry fuse/relay block diagram, 1993 dodge dakota fuse panel, 1993 dodge viper fuse panel diagram, fuse block for a 92 Chrysler New Yorker, wheres the the battery relay on 93 new yorker,

VW Rabbit, Jetta, Scirocco, Pick-up & Convertible (gasoline engine) 1975-1992 Auto Repair Manua

0

Filed Under (volkswagen) by admin on 03-09-2009

VW Rabbit, Jetta, Scirocco, Pick-up & Convertible (gasoline engine) 1975-1992 Auto Repair Manual
Provides service, repair and maintenance information for all Rabbit, Golf, Jetta, Scirocco, Pick-up and Cabriolet Convertible gasoline models (1975-1992) Rabbit Convertible (1980-1992)

1992 Lexus SC 400 Window Regulator: Technical Service Bulletins

0

Filed Under (Lexus) by admin on 27-09-2010

download
To improve power door window serviceability on SC 400/300, GS 300, and ES 300, a wire regulator subassembly is now available as separate supply parts. REPAIR PROCEDURES: ^ ^ ^ Verify motor operates properly. If the motor must be replaced, change the complete regulator assembly. If motor operation is correct, replace only the regulator subassembly. Use the following procedures when replacing the subassembly. 1992 Lexus SC 400 V8-4.0L (1UZ-FE) WINDOW REGULATOR DISASSEMBLY: 1. REMOVE COVER PLATE ^ Remove the two screws and cover plate; see figure 1. Note: The screws and cover plate are reusable. ^ Pry up the cover plate tab using a small flat-head screwdriver and remove the plate. Use care not to damage the motor housing; see figure 2. Note: The cover plate is not reusable. 2. REMOVE WINDOW REGULATOR DRUM AND WIRE GUIDE FROM MOTOR HOUSING USING NEEDLE NOSE PLIERS (SEE FIGURE 3). Caution: Do not use a flat-head screwdriver to remove the drum and wire guide. WINDOW REGULATOR INSTALLATION: 1. INSERT THE WINDOW REGULATOR DRUM INTO THE MOTOR HOUSING. 1992 Lexus SC 400 V8-4.0L (1UZ-FE) Note: ^ To prevent the window regulator drum and cable from coming off, do not tilt the drum, subject it to shocks or use force. If the cable comes off the drum, do not rewind the cable or reuse it. After the window regulator is installed, do not operate it manually (some window regulators do not utilize a stopper). ^ Multipurpose grease (P/N OO289-1WG00) should be applied to all moving parts, especially inside the motor housing and sides of the window regulator drum. Type “A” holding tool

Related entry:

replacing regulator in ls 400,

BMW 3/5 Series 1982-1992 Auto Repair Manual

0

Filed Under (BMW) by admin on 03-09-2009

BMW 3/5 Series 1982-1992 Auto Repair Manual
Provides service, repair and maintenance information for 3/5 Series. 318i (1984-1985), 325, 325e and 325es (1984-1988), 325i, 325is and 325ic (1987-1990), 525i (1989-1990), 528e (1982-1988), 533i (1983-1984), 535i and 535is (1985-1992)