service manual of nissan vanette


You are searching repair manual in PDF format about service manual of nissan vanette use another keyword for search another post or files




BMW 3 5 6 7 SERIES SERVICE REPAIR MANUAL

0

Filed Under (BMW) by admin on 06-09-2009

covered such as : Accessories & Electrical, Accessories / Safety Equipment, Electrical Component Locator, Electrical , Technical Service Bulletins Air Conditioning and Heat, Air Conditioning and Heat, Electrical Component Locator, Technical Service Bulletins, Automatic Transmission, Electrical Component Locator, Technical Service Bulletins, Automatic Transmission Service, Brakes, Electrical Component Locator, Technical Service Bulletins, Engine Mechanical, Engine Cooling, Engines, Technical Service Bulletins, Engine Performance, Electrical Component Locator, Emmissions, Engine Performance, Fuel Systems, Technical Service Bulletins, Tune Ups, Engine Performance (cont’d), Emission Recalls, Technical Tips, * General, Technical Service Bulletins, General Trouble Shooting, General Information, * Maintenance, General Procedures and Guidelines, Power train, Drive Axles, Electrical Component Locator, Technical Service Bulletins, * Steering & Suspension, Electrical Component Locator, Steering, Suspension, Technical Service Bulletins, Wheel Alignment, * Technical Service Bulletins, Recalls, & Technical Information, Technical Service Bulletins, Emission Recalls, * Technical Tips Wiring Diagrams

2005 – 2009 Nissan FRONTIER, Nissan XTERRA, Nissan PATHFINDER, FRONT AIR BAG CRASH ZONE SENSOR

0

Filed Under (Nissan) by admin on 04-01-2011

download
SERVICE PROCEDURE 1. Set the parking brake. 2. Connect C-III to the vehicle. 3. Use C-III to check for Air Bag DTCs. a. Navigate C-III to Air Bag Direct Diagnostic Mode. b. Make sure to check both SELF DIAG RESULTS and SELF-DIAG [PAST]. • SELF-DIAG [PAST] is under Special function. • If there are any DTCs stored for AIR BAG other than B1033, B1034 and/or B1035, perform repairs as needed, and then erase DTC before continuing with this procedure. • Diagnosis and repair for DTCs other than B1033, B1034, and/or B1035 is not covered by this bulletin. NOTE: All DTCs (except B1033, B1034, and B1035) must be repaired and erased before continuing with this procedure. 4. Disconnect C-III from the vehicle. 5. Start the engine and let it idle for about 5 seconds. 6. Turn the ignition OFF. 7. WARNING: Prep the vehicle for Crash Zone Sensor replacement as follows: The following are VERY IMPORTANT to prevent unexpected air bag deployment. • Remove the ignition key / Intelligent Key from the cabin of the vehicle and set aside, away from the vehicle (this will prevent accidentally turning the ignition ON). • Make sure the ignition remains OFF until after the new sensor is completely installed. • Make sure no one is in the vehicle cabin and no one enters the vehicle cabin until after the sensor is completely installed. • Wait for all control units to “power down” (at least 1 minute) before continuing. 8. Locate the Crash Zone Sensor (see Figure 2). Crash Zone Sensor Cover 9. Remove the 2 Crash Zone Sensor nuts shown in Figure 3. • Discard these nuts. They will not be reused. 10. Remove the Crash Zone Sensor Cover. 11. Disconnect the electrical connector shown in Figure 4.

2000 Jeep Grand Cherokee Housing Assembly HVAC: Service and Repair

0

Filed Under (Jeep) by admin on 17-08-2010

download
Housing Assembly HVAC: Service and Repair The heater-A/C housing assembly must be removed from the vehicle and the two halves of the housing separated for service access of the heater core, evaporator coil, blend-air door(s), and each of the various mode control doors. WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS, REFER TO AIR BAGS AND SEAT BELTS/AIR BAGS BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. FAILURE TO TAKE THE PROPER PRECAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY. REMOVAL 1. Disconnect and isolate the battery negative cable. 2. Remove the instrument panel from the vehicle. Refer to: Body and Frame, Interior Trim, Dashboard/Instrument Panel, Service and Repair, Instrument Panel Service Procedures, Instrument Panel Assembly Replacement, See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and Repair/Instrument Panel Service Procedures/Instrument Panel Assembly Replacement 3. Recover the refrigerant from the refrigerant system. See: Refrigerant/Service and Repair 4. Disconnect the liquid line refrigerant line from the evaporator inlet tube See: Hose/Line HVAC/Service and Repair. Install plugs in, or tape over all of the opened refrigerant line fittings. 5. Disconnect the suction line refrigerant line from the evaporator outlet tube See: Hose/Line HVAC/Service and Repair. Install plugs in, or tape over all of the opened refrigerant line fittings. 6. Disconnect the heater hoses from the heater core tubes. Clamp off the heater hoses to prevent loss of coolant. Install plugs in, or tape over the opened heater core tubes. 7. If the vehicle is equipped with the manual temperature control system, unplug the heater-A/C system vacuum supply line connector from the tee fitting near the heater core tubes. 8. Remove the coolant reserve/overflow bottle from the passenger side inner fender shield. 9. Remove the Powertrain Control Module (PCM) from the passenger side dash panel in the engine compartment and set it aside. Do not unplug the PCM wire harness connectors.

NISSAN PERIODIC MAINTENANCE SCHEDULE NISSAN MICRA

0

Filed Under (Nissan) by admin on 11-04-2010

download
ENGINE MAINTENANCE (Petrol Engine) Replace engine oil Replace engine oil filter Inspect drive belts Inspect cooling system
Page 1© NISSAN NISSAN PERIODI CMAINTENANCE SCHEDULE NISSAN MICRA 15,000 KM Inspect brake, clutch and automatic
trans-axle fluids Inspect manual trans-axle gear oil Inspect power steering fluid and lines Inspect brake, clutch and exhaust systems
Inspect steering gear and linkage, axle and suspension parts and front driveshafts Inspect wheel alignment (if necessary rotate
tyres and balance Inspect brake pads, rotors and other brake components Inspect brake linings, drums and other brake
components Inspect foot brake, parking brake and clutch Lubricate locks, hinges & hood latch Inspect seat belts, buckles, retractors,
anchors & adjuster Clean or replace ventilation filter Replace brake fluid (Severe conditions only)

2007 Mercedes Benz C 230 Maintenance: Service Intervals

0

Filed Under (Mercedes-Benz) by admin on 08-09-2010

download
The type of maintenance service due is indicated in the multifunction display: Basic service (A) Extended service (B) Note: Vehicles equipped with FSS PLUS Flexible Service System PLUS) only: The interval between maintenance services depends on your driving habits. A gentle driving style, moderate engine speeds and the avoidance of short-distance trips will lengthen the interval between services. Clearing the maintenance service indicator The maintenance service indicator is automatically cleared. – after approximately 10 seconds when you switch on the ignition or when reaching the maintenance service threshold while driving – after approximately 30 seconds, once the suggested maintenance service term has passed You can also clear it yourself