slk Throttle Switch


You are searching repair manual in PDF format about slk Throttle Switch use another keyword for search another post or files



  slk Throttle Switch Direct Download speed 5787 Kb/s

  slk Throttle Switch Full Version speed 6767 Kb/s




2004 Honda Element EX ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH)

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Check the engine oil level. Is the level OK? YES- Go to step 2 . NO- Adjust the engine oil to the proper level, then go to step 14 . 2. Turn the ignition switch ON (II). 3. Clear the DTC with the HDS. 4. Do the VTEC TEST in the INSPECTION MENU with the HDS. Is the result OK? YES- Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch) and the ECM/PCM. NO- Go to step 5 . 5. Check the result of step 4 . Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Failure Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Open Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) SIG Line Open Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) GND Line Open Is the test result any of the above? YES- Go to step 6 . NO- Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch). If it is OK, replace the rocker arm oil control solenoid (VTEC solenoid valve) (see step CMP SENSOR A REPLACEMENT ), then go to 14 . 6. Turn the ignition switch OFF. 7. Disconnect the rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector. 8. Check for continuity between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminals No. 1 and No. 2.

Related entry:

ignition switchwiring digram for m benz 300e 1991, 2006 jeep liberty ignition switch repair, ford windstar 3 8L V6 rocker arm torque spec, ignition guid ford mustang 1997, how to replace ignition switch on 2004 impala, 1994 ford escort lx ignition lock pin replacement, 1940 buick key removal, brake light switch 94 silverado, 2001 chevy cavalier rocker arm torque specs free manual, sunroof switch replacement instructions 2008 scion tc,

1991 Ford F 150 Ignition Switch Service and Repair

0

Filed Under (Ford) by admin on 29-07-2010

download
Removal 1. Disconnect the battery ground cable. 2. Remove steering column shroud and lower the steering column. Refer to Steering Column: Service and Repair: Removal/Installation . 3. Disconnect the switch wiring at the multiple plug. 4. Remove the two nuts that retain the switch to the steering column. 5. LIFT the switch VERTICALLY UPWARD to disengage the actuator rod from the switch and remove switch. Installation 1. When installing the ignition switch, both the locking mechanism at the top of the column and the switch itself must be in LOCK position for correct adjustment. To hold the mechanical parts of the column in LOCK position, move the shift lever into PARK (with automatic transmissions) or REVERSE (with manual transmissions), turn the key to LOCK position, and remove the key. New replacement switches, when received, are already pinned in LOCK position by a metal shipping pin inserted in a locking hole on the side of the switch. 2. Engage the actuator rod in the switch. Must be inserted in the slot of the sliding, white carrier. 3. Position the switch on the column and install the retaining nuts, but do not tighten them. 4. Move the switch UP and DOWN along the column to locate the mid-position of rod lash. Tighten the two ignition switch retaining nuts (TOP NUT FIRST to minimize rod binding) to 4.51-7.34 N.m(40-65 in-lb) . 5. Remove the lockpin. Connect the battery cable, and check for proper start in PARK or NEUTRAL. Also, ensure the start circuit cannot be actuated in the DRIVE and REVERSE position and that the engine will shut off in either DRIVE, REVERSE or NEUTRAL. If the engine will not shut off in the above positions then the switch is NOT adjusted properly. The switch will have to be re-adjusted. Refer to Ignition Switch: Adjustments . 6. Raise the steering column into position at instrument panel. Refer to Steering Column: Service and Repair: Removal/Installation . 7. Confirm that accessories are deactivated with ignition switch in OFF position, and that accessories are operable with switch in RUN position.

Related entry:

how to change the actuator rod in a 1996 mercury sable, 1990 ford ignition lock actuator, 1996 sable ignition actuator rod removal, 2009 Econoline key-in-ignition warning switch wiring harness, dakota reverse light switch, ford crown victoria1996 iginition switch actuator, Ignition Cylinder Actuator Rod Replacement 1990 ford f150, reverse light switch pontiac g5, winnebago chevy p30 1996 passage reverse light not working,

2000 Honda Accord DX THROTTLE BODY CLEANING

0

Filed Under (Honda) by admin on 17-03-2011

download
SYMPTOM When the engine is first started after the vehicle has sat overnight, customers may “feel” the release of the throttle plate through the accelerator pedal. Some describe it as a one-time “pop” sensation. Customers may have trouble explaining this phenomenon because: They can’t repeat it because it only happens one time, when the engine is cold. The accelerator pedal works normally at all other times. There are no other symptoms. It may be intermittent, happening only during cooler weather. PROBABLE CAUSE The symptom is caused by normal buildup of contaminants in the throttle bore, combined with expansion and contraction of the throttle body. CORRECTIVE ACTION Partially remove the throttle body, and clean it with Honda carburetor cleaner or throttle plate and induction cleaner. REPAIR PROCEDURE 1. Remove the breather tube from the air intake duct, unclip the vacuum lines from the duct, and remove the duct from the throttle body. See Fig. 1 . Fig. 1: Removing Air Intake Duct 2. Disconnect the TPS and MAP connectors from the throttle body. 3. Remove the throttle cable and, if equipped, the cruise control actuator cable from the throttle body. 4. Remove the throttle body mounting nuts and bolts, then slide the throttle body off its studs on the intake manifold chamber. Leave the coolant hoses connected. See Fig. 2 . 5. Put a shop towel under the throttle body, open the throttle, then clean out any contaminants from the intake manifold side of the throttle body with carburetor cleaner or throttle plate and induction cleaner. See Fig. 3 . NOTE: To avoid damaging the idle air control valve (IACV), spray the cleaner through the back of the throttle body, not the front.

Related entry:

1993 toyota 4runner vacuum diagram, how to relearn throttle body on 07 Ford Freestyle, how to replaced a throttle body on saturn ion 2007 you tube, how to disassemble an isuzu rodeo throttle body, throttle body factory relearn procedure 2007 ford five hundred, 2009 ford escape throttle actuator control code P2119, 2004 AMANTI THROTTLEBODY ELECTRICAL DIAGRAMS, throttle body B14 nissan sunny, idles too high idle malibu relearn 2001, adusting throttlebody on 2005 saturn ion,

1996 Jeep Cherokee Neutral Safety Switch: Service and Repair Automatic

0

Filed Under (Jeep) by admin on 17-09-2010

download
REMOVAL 1. Raise vehicle. 2. Disconnect switch wire harness connector. 3. Pry washer lock tabs upward and remove switch attaching nut and tabbed washer. 4. Remove switch adjusting bolt. 5. Slide switch off manual valve shaft. INSTALLATION 1. Disconnect shift linkage rod from shift lever on left side of transmission. 2. Rotate manual shift lever all the way rearward. Then rotate lever forward two detent positions to Neutral. 3. Install switch on manual valve shaft and install switch adjusting bolt finger tight. Do not tighten bolt at this time. 4. Install tabbed washer on manual valve shaft and install switch attaching nut. Tighten nut to 6.9 Nm (61 inch lbs.) torque but do not bend washer lock tabs over nut at this time. 5. Verify that transmission is in Neutral. 6. Rotate switch to align neutral standard line with vertical groove on manual valve shaft. 7. Align switch standard line with groove or flat on manual valve shaft. 8. Tighten switch adjusting bolt to 13 Nm (108 inch lbs.) torque. 9. Bend at least two washer lock tabs over switch attaching nut to secure it. 10. Connect shift linkage rod to shift lever on left side of case. 11. Connect switch wires to harness and lower vehicle. 12. Check switch operation. Engine should start in Park and Neutral only.

Related entry:

where is the neutral safety switch located on a 2000 grand marquis, 2006 mazda6 how to bypass saftey neutral switch, 2007 mazda3 neutral safety switch location, Replace 2008 Mazda 3 Neutral Safety switch, mazda 3 neutral safety switch location, 87-17277T, changing neutral safety switch on 2005 Mazda 6, 1995 4l60e neutral safety switch wiring diagram, googel where is the nutrel safty switch on 2003 impala, 2007 mazda 3 neutral safety switch replacement,

1998 GMC C 1500 Throttle Position Sensor Description and Operation

0

Filed Under (GM) by admin on 04-11-2010

download
DESCRIPTION The Throttle Position (TP) sensor is a potentiometer. The TP sensor is connected to the throttle shaft on the throttle body. By monitoring the voltage on the signal line, the VCM calculates throttle position. As the throttle valve angle is changed (accelerator pedal moved), the TP sensor signal also changes. At a closed throttle position, the output of the TP sensor is low. As the throttle valve opens, the output increases so that at Wide Open Throttle (WOT,) the output voltage should be above 4.0 volts. PURPOSE The VCM calculates fuel delivery based on throttle valve angle (driver demand). A broken or loose TP sensor may cause intermittent bursts of fuel from an injector. This may cause an unstable idle because the VCM detects the throttle is moving.