toyota camry exploded view
You are searching repair manual in PDF format about toyota camry exploded view use another keyword for search another post or files
Filed Under (Toyota) by admin on 22-04-2010
1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of way. On Camry, remove coolant reservoir tank if it interferes with timing belt removal. Remove engine control (torque) rod from front of engine. 3. On all models, remove accessory drive belts. Using floor jack, slightly raise engine to remove weight from right (timing belt side) engine mount at timing belt cover.
4. Remove right (timing belt side) engine mount and bracket from front of engine. Remove spark plugs. Remove No. 2 timing belt cover and gaskets. See Fig. 1 . 5. Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. 6. Ensure timing mark on crankshaft pulley aligns with “0″ mark on No. 1 timing belt cover. Ensure hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If hole in camshaft sprocket is not aligned with alignment mark, rotate crankshaft clockwise one full revolution.
Filed Under (Toyota) by admin on 26-06-2010
Introduction Under certain driving conditions, some 1998 – 1999 model year Camry and Solara vehicles may exhibit a M.I.L. “ON” with DTCs P0440, P0441 and P0446 stored due to an inoperative Vapor Pressure Sensor 3 way Vacuum Switching Valve (VSV). An improved Vapor Pressure Sensor VSV has been developed to correct this condition. S 1998 – 1999 model year Camry & Solara vehicles. Applicable Vehicles Parts PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME QTY Information 90910–12109 90910–12271 Vapor Pressure Sensor VSV 1
Filed Under (Toyota) by admin on 02-05-2010
Fig. 14 Exploded View Of Disc Brake Assembly 5 Exploded View Of Disc Brake Assembly. 1989 Celica w/AWD 16 Exploded View Of Disc Brake Assembly. 1990 Celica NOTE: If a squealing noise occurs from the front brakes while driving, check the pad
wear indicator. If there are traces of the indicator contacting the rotor disc, the brake pad
should be replaced.
z Remove front wheel
z Temporarily fasten the rotor disc with the hub nuts.
z Inspect pad lining thickness
Filed Under (Toyota) by admin on 04-06-2010
Some customers may experience a water leak at the front floor area. Water may be Introduction entering the body due to a body sealer void on the engine compartment rear wall, near the upper door hinge. Repair 1. Raise the vehicle. On the side of the vehicle that has the water leak, remove the front Procedure wheel and the front fender plastic liner. 2. Examine (with flash light and mirror) the body sealer condition on the engine compartment rear wall, near the upper door hinge. Also examine the sealer condition inside the inner fender box frame structure with access holes (see illustration).
Filed Under (Ford) by admin on 02-05-2010
REMOVAL AND INSTALLATION Exterior Mirrors — Exploded View Printable View (364 KB) Aero-Style Mirror
NOTE: LH exterior mirror shown, RH exterior mirror similar. 14631 Exterior mirror electrical connector W705760 Exterior mirror nut (3 required) 17K707 Exterior mirror glass — Dampener springs (part of 17K707) Exterior mirror motor screw (3 required) (part of 17D696)
17D696 Exterior mirror motor — Exterior mirror lower cover screw (3 required) (part of 17682 RH/ 17683 LH) — Exterior mirror lower cover (part of 17682 RH/ 17683 LH) 17D742 RH/ 17D743 LH Exterior mirror upper 17682 RH/ 17683 Exterior mirror