toyota prado auto gearbox removal


You are searching repair manual in PDF format about toyota prado auto gearbox removal use another keyword for search another post or files



  toyota prado auto gearbox removal Direct Download speed 5787 Kb/s

  toyota prado auto gearbox removal Full Version speed 6767 Kb/s




WATER LEAK AT FRONT FLOOR ’02 – ’06 Toyota Camry (TMMK), ’04 – ’06 Toyota Solara Coupe, & ’05 – ’06 Toyota Avalon

0

Filed Under (Toyota) by admin on 04-06-2010

download
Some customers may experience a water leak at the front floor area. Water may be Introduction entering the body due to a body sealer void on the engine compartment rear wall, near the upper door hinge. Repair 1. Raise the vehicle. On the side of the vehicle that has the water leak, remove the front Procedure wheel and the front fender plastic liner. 2. Examine (with flash light and mirror) the body sealer condition on the engine compartment rear wall, near the upper door hinge. Also examine the sealer condition inside the inner fender box frame structure with access holes (see illustration).

Related entry:

1992 Toyota Tercel Repair Manual, unlatching relay assembly above glove compartment in toyota tacoma, 2007 Toyota Sequoia fuse location, toyota dyna xzu382 engine repair manual egr sistem, toyota tazz carburetor manual, hi lux p1226, how to remove the glove box on 2010 Toyota Tacoma, トヨタ 09950-20017, 2001 toyota tazz 1300 timing adjustment, toyoto code po 352,

1994 Toyota Camry DX TOYOTA’ ’2.2L 4-Cylinder – Gasoline TIMING BELT REMOVAL & INSTALLATION

0

Filed Under (Toyota) by admin on 22-04-2010

download
1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of way. On Camry, remove coolant reservoir tank if it interferes with timing belt removal. Remove engine control (torque) rod from front of engine. 3. On all models, remove accessory drive belts. Using floor jack, slightly raise engine to remove weight from right (timing belt side) engine mount at timing belt cover.
4. Remove right (timing belt side) engine mount and bracket from front of engine. Remove spark plugs. Remove No. 2 timing belt cover and gaskets. See Fig. 1 . 5. Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. 6. Ensure timing mark on crankshaft pulley aligns with “0″ mark on No. 1 timing belt cover. Ensure hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If hole in camshaft sprocket is not aligned with alignment mark, rotate crankshaft clockwise one full revolution.

Related entry:

strip engine for toyata camry 220si, how to replace trunk lock cylinder in Toyota Avalon, exhaust diagram for 2001 camry 2 2, 2002 toyota camry 3 0L V6 torque specification valve cover bolts, 2010 toyota camry front axel nut size, 1997 ford camry timing belt motor 2 2, resetting the idle on a 2005 camry, 1992 toyota camry exhaust system diagram, whats 91 camry 4 cylinder engine, cam timing marks 1992 toyota 2 2,

Retro fit of the Audi Auto dimming rear view mirror

0

Filed Under (Audi) by admin on 16-06-2010

download
recommend you disconnect the battery first, and make sure you ground yourself to the vehicle chassis, as you will be working very close to the Airbag system. 1. First of all remove the centre light surround. 2. Remove the three screws that hold the main body in place, one is behind the sun glasses holder. 3. Remove the main body of the internal light console. And disconnect the main plug, as we will need to fit one of the connections on 4. This the tricky bit, remove the “A” Pillar interior trim. The trick is to get your fingers behind the very top of the trim, once you have two fingers behind the trim, pull quite hard until you see the top clip pop out. There are three in total, don’t be scared to give it some force, as the clips will give. Now you have this piece of trim out, remove the small piece of trim down by the door hinges, along with the fuse cover. The Gearbox wire can to be connected to the following depending if you have an auto of manual transmission. Manual gearbox: 32-pole Gray connector (vehicle on-board control system) by soldering to PIN 9 (backwards signal) Automatic gearbox: Beige connector (central control device comfort system) PIN 8 The location differs depending on what model you have. However I did not connect this wire, as I could not find the unit. But I believe it’s behind the steering wheel. 8. The best fuse block to use for connecting the 12 volt ignition is the Brown fuse connector

2004 Ford Explorer Radiator Cooling Fan and Shroud Removal

0

Filed Under (Ford) by admin on 22-02-2011

download
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-00. 2. If servicing the radiator, drain the cooling system. For additional information, refer to Cooling System Draining, Filling and Bleeding in this section. 3. Remove the parts in the order indicated in the following illustrations and tables. 4. To install, reverse the removal procedure. If servicing the radiator, fill the cooling system. For additional information, refer to Cooling System Draining, Filling and Bleeding in this section. Item 9: Lower Degas Bottle Hose Removal Note 1. Remove the lower degas bottle hose from the clip on the radiator lower fan shroud. Item 10: A/C Tube Removal Note 1. On 4.6L engines, detach the A/C tube from the retainers. Item 11: Transmission Cooler and A/C Tubes Removal Note 1. Disconnect the transmission cooler tubes. Remove the safety retainers from the transmission cooler tubes. Using the special tool, disconnect the quick coupler. If equipped, loosen and remove the screw clamp from the hose. 2. Remove the A/C tube brackets from the engine front cover. Item 12: Radiator Fan Shroud Screw Removal Note 1. Not all vehicles will have these radiator fan shroud screws. If vehicle is equipped with these screws, please discard them. Item 15: Cooling Fan Removal Note 1. CAUTION: Cardboard must be placed against the radiator when removing the cooling fan. Failure to follow these procedures can result in damage to the vehicle. Place a piece of cardboard against the radiator to prevent damage while removing the cooling fan. 2. Using the special tools, remove the fan blade and the clutch assembly. Item 17: Radiator Lower Fan Shroud Removal Note 1. Remove the power steering tube from the clip on the radiator lower fan shroud. Item 19: Radiator Bracket Bolt Removal Note 1. If necessary, remove the radiator brackets. Item 21: A/C Condenser Support Bracket Bolt Removal Note 1. If necessary, remove the condenser brackets. Item 22: Radiator Removal Note 1. NOTE: It will be necessary to lift the radiator assembly up off the mounts and set it on the frame in order to separate the A/C condenser from the radiator. NOTE: RH side shown, LH side similar. Remove the radiator up off the mounts and set it on the frame. 2. Remove the left inner air deflector from the A/C condenser. 3. Remove the right inner air deflector from the A/C condenser.

Related entry:

how to install ac condensor on 96 dodge dokota, kia carens automatic transmission removal, how to take glove box out of chevy traverse, remove knee bolster 2010 mazda 3, how to replace radiator for a 2004 chevrolet trailblazer video, how to remove the dash in a 1998 chevy c1500, how to remove center arm rest on a 1999 mercury grand, 04 explorer 4 6 cooling diagram, ford remove upholsery, dash removal sprinter,

2003 Ford Explorer Radiator Cooling Fan and Shroud Removal

0

Filed Under (Ford) by admin on 18-02-2011

download
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-00. 2. If servicing the radiator lower fan shroud or the radiator, drain the cooling system. For additional information, refer to Cooling System Draining, Filling and Bleeding in this section. 3. Remove the parts in the order indicated in the following illustrations and tables. To remove individual parts, only carry out the listed steps: 4. To install, reverse the removal procedure. If servicing the radiator lower fan shroud or the radiator, fill and bleed the cooling system. For additional information, refer to Cooling System Draining, Filling and Bleeding in this section. Item 9: Lower Degas Bottle Hose Removal Note 1. Remove the lower degas bottle hose from the clip on the radiator lower fan shroud. Item 10: A/C Tube Removal Note 1. On 4.6L engines, detach the A/C tube from the retainers. Item 11: Transmission Cooler and A/C Tubes Removal Note 1. Disconnect the transmission cooler tubes. Remove the safety retainers from the transmission cooler tubes. Using the special tool, disconnect the quick coupler. If equipped, loosen and remove the screw clamp from the hose. 2. Remove the A/C tube brackets from the engine front cover. Item 12: Radiator Fan Shroud Screw Removal Note 1. Not all vehicles will have these radiator fan shroud screws. If vehicle is equipped with these screws, please discard them. Item 15: Cooling Fan Removal Note 1. CAUTION: Cardboard must be placed against the radiator when removing the cooling fan. Failure to follow these procedures can result in damage to the vehicle. Place a piece of cardboard against the radiator to prevent damage while removing the cooling fan. 2. Using the special tools, remove the fan blade and the clutch assembly. Item 17: Radiator Lower Fan Shroud Removal Note 1. Remove the power steering tube from the clip on the radiator lower fan shroud. Item 19: Radiator Bracket Bolt Removal Note 1. If necessary, remove the radiator brackets. Item 21: A/C Condenser Support Bracket Bolt Removal Note 1. If necessary, remove the condenser brackets. Item 22: Radiator Removal Note 1. NOTE: It will be necessary to lift the radiator assembly up off the mounts and set it on the frame in order to separate the A/C condenser from the radiator. NOTE: RH side shown, LH side similar. Remove the radiator up off the mounts and set it on the frame. 2. Remove the left inner air deflector from the A/C condenser.

Related entry:

toyota rav 4 radiator support, 2009 dODGE journey REMOVING RADIATOR, how to remove fan shroud 2006 f-350, 1999 ford taurus radiator removel, 1999 chevy venture van radiator removal, where is the ac fan relay located in a 2008 kia sedona, 1999 Ford Taurus Radiator Removal, radiator drain 2005 freelander, 2010 chevy cobalt radiator removal, how to remove clutch fan brackett 1996 lexus ls400,