toyota runx 2004


You are searching repair manual in PDF format about toyota runx 2004 use another keyword for search another post or files



  toyota runx 2004 Direct Download speed 5787 Kb/s

  toyota runx 2004 Full Version speed 6767 Kb/s




COLD AIR SYSTEM Installation Instructions 2003-2004 Toyota Corolla 2002-2004 Toyota Matrix XR

0

Filed Under (Toyota) by admin on 16-04-2010

download
Removing the stock air inlet system
a) Before removing any of the O.E. components, label each individual part so that no components become mixed up during the installation process. There are two Vacuum Switching Valves (VSV), and one air flow meter that have electrical and/or vacuum connections going to them. Be sure to label these connections before disconnecting them.
Remove b) Remove the two nuts and two plastic rivets that hold the plastic engine cover on. The
plastic rivets may be gently lifted with a small screwdriver. Remove the cover. c) Remove the bolt in the radiator support that holds the battery bracket. Unhook the rod at the rear of the battery bracket. Remove the battery from the vehicle

Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool

0

Filed Under (Audi) by admin on 15-09-2009

Check the following wire connection for open circuit according to wiring diagram:Relay carrier in E-box, plenum chamber, position 3Terminal Harness connector atignition coils Terminal 8 1 Specified value: Wire resistance max 1.5 – If necessary, repair wire connection. Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool, Engi…Page 5 24-158 If no malfunctions are found in wires: – Check voltage supply of Motronic Engine Control Module (ECM) voltage supply relay – J271 – Page 24-158 . – Check activation of Motronic Engine Control
Module (ECM) voltage supply relay – J271 – Page 24-159 . Checking voltage supply If specified value is not obtained:
- Connect multimeter for voltage measurement as follows. Relay carrier in E-box, plenum chamber, position 3
Terminal

ENGINE MISFIRE 2003-2004 Mustang, 1999-2004 Navigator 2002-2003 Blackwood 2003-2005 Aviator 2003-2004 Marauder

0

Filed Under (Ford) by admin on 11-05-2010

download
Some 1999-2004 Navigator, 2002-2003 Blackwood, 2003-2005 Aviator, 2003-2004 Marauder and 2003-2004 Mustang vehicles built before 12/19/2004 equipped with 4.6L 4V/5.4 4V engine may exhibit a runs rough, lacks power, and engine misfire, prompted by a MIL light and DTC codes P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, and P0316. ACTION Diagnose engine for engine misfire concern. If diagnostics determine an engine misfire which is characterized by leakage through exhaust valve(s), only replace the affected cylinder head(s). SERVICE PROCEDURE

WATER LEAK AT FRONT FLOOR ’02 – ’06 Toyota Camry (TMMK), ’04 – ’06 Toyota Solara Coupe, & ’05 – ’06 Toyota Avalon

0

Filed Under (Toyota) by admin on 04-06-2010

download
Some customers may experience a water leak at the front floor area. Water may be Introduction entering the body due to a body sealer void on the engine compartment rear wall, near the upper door hinge. Repair 1. Raise the vehicle. On the side of the vehicle that has the water leak, remove the front Procedure wheel and the front fender plastic liner. 2. Examine (with flash light and mirror) the body sealer condition on the engine compartment rear wall, near the upper door hinge. Also examine the sealer condition inside the inner fender box frame structure with access holes (see illustration).

2004 Hyundai Sonata 2003-2004 Hyundai Santa FE 2004 Kia Optima no spark Problem and Repair

0

Filed Under (Hyundai) by admin on 25-04-2010

download
1. At the crank position sensor, check for battery voltage to be present on the Red wire with the key on and cranking. The Black wire should be a good ground and the Blue wire should have 5 volts on it from the computer. One may have to disconnect the crank sensor to check for the 5 volt reference. 2. During crank look for a good 5 volt square wave signal on the Blue wire. 3. Check at the ignition coils for good battery voltage key on and cranking. If there is a loss of voltage during crank check the ignition failsafe relay. 4. Check for any stored engine codes. Crankshaft Position (CKP) Sensor Ignition Failsafe Sensor The ignition failsafe sensor supplies battery voltage to the ignition coils. The ignition coils can look like they have good battery voltage key on but during crank the ignition failsafe relay can stop sending voltage to the ignition coils.