Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Engine Electrical > Firing Orders Firing Orders To avoid confusion, always replace spark plugs and wires one at a time. Replacing spark plugs and wires one at a time will help prevent incorrect wire routing or cross-firing resulting from an incorrect firing order. If more than one wire is to be disconnected at a single time, be sure to tag all of the cables to assure proper installation. Also, be disconnecting the cables, compare the firing order and routing to these diagrams and note any differences for installation purposes. This will help assure the wires are properly installed.

download
2004 model year Sienna vehicles may experience power sliding door inoperative conditions. A new Power Slide Door Motor, Center Bracket No. 1, and Center Hinge have been made available to improve the durability of this system. Repair Procedure Remove Power Slide Door Motor, Cable Assembly, and Center Hinge. Remove Slide Door Window Garnish. A. Fully open the slide door window. B. Remove the glass run. C. Using a screwdriver, disengage the clip and remove the garnish. HINT: Tape the screwdriver tip before use. D. Using the taped screwdriver, disengage the 2 claws and remove the inner weatherstrip from the garnish. Repair Procedure (Continued) 2. Remove Side Trim Board Cover Rear. A. Remove the 2 screws. B. Using the taped screwdriver, disengage the 8 claws and remove the cover together with the window control switch. C. Remove the 2 screws and window control switch. 3. Remove Rear Door Trim Board Sub–assembly. A. Remove the screw. B. Using the taped screwdriver, disengage the 9 clips and remove the trim board. HINT: In order to prevent the door panel from being damaged, cover the areas with protective tape as indicated by the arrows in the illustration. 4. Remove Rail End Molding. A. Open the quarter glass. B. Using the taped screwdriver, disengage the clip and 2 claws, and remove the rail end molding.

download
Introduction The sliding door front striker plate and lock assembly on 2004 – 2006 model year Sienna vehicles have been redesigned in order to address customer complaints of rattles that occur under certain driving conditions. The improved front striker plate and lock assembly have a new coating that will reduce noise from contact between the front striker plate and the sliding door lock assembly when in the closed position. Refer to TIS: S 2004 or 2005 model year Sienna Repair Manual: Engine Hood/door: Slide Door: Overhaul.
S 2006 model year Sienna Repair Manual: Engine Hood / Door: Slide Door: Disassembly and Reassembly, Installation.

download
Replacement Interval Guide Toyota recommend: 1993: Replacement every 60,000 miles or 5 years, whichever occurs first. 1994 : Replacement every 63,000 miles or 5 years, whichever occurs first. 1996 : Replacement every 60,000 miles or 5 years, whichever occurs first (Colorado only). The previous use and service history of the vehicle must always be taken into account. Check For Engine Damage Check For Engine Damage Removal Removal 1. Remove timing belt cover [1]. 2. Turn crankshaft clockwise until timing marks aligned [2]. 3. Ensure timing marks aligned: 1KZ-T/TE: [3]. 1HD-FT/1HD-FTE: [4]. 4. Evenly slacken and remove automatic tensioner unit bolts [5]. 5. Remove: Automatic tensioner unit [6]. Tensioner pulley bolt [7]. Tensioner pulley [8]. Timing belt. Installation Installation 1. 2. 3. 4. 5. 6. 7. Check tensioner pulley for smooth operation [8]. Replace if necessary. Remove dust cover. Check tensioner body for leakage or damage [6]. Check pushrod protrusion is 9,0-9,8 mm [9]. Check pushrod does not move when pushed against a firm surface. If pushrod moves: Replace automatic tensioner unit. Slowly compress pushrod into tensioner body until holes aligned. Use press. Retain pushrod with 1,5 mm Allen key through hole in tensioner body [10]. Fit dust cover. Ensure timing marks aligned [2]. Ensure timing marks aligned: 1KZ-T/TE: [3]. 1HD-FT/1HD-FTE: [4]. 8. 9. 10. 11. 12. 13. 14. 15. 16. Fit timing belt in anti-clockwise direction, starting at lower sprocket. Ensure belt is taut between sprockets. Fit tensioner pulley [8]. Tighten bolt to 34 Nm [7]. Push tensioner pulley against belt. Install automatic tensioner unit [6]. Tighten bolts evenly to 13 Nm [5]. Remove Allen key from tensioner body to release pushrod. Turn crankshaft two turns clockwise. Ensure timing marks aligned [2] & [3] or [4]. If not: Repeat installation and tensioning procedures. Install components in reverse order of removal. Reset timing belt replacement warning lamp as follows: -Runner/Landcruiser: Remove grommet in speedometer housing. Depress switch using a thin screwdriver [11]. 17. Colorado: Remove speedometer housing. Remove screw indicated and insert in alternative location [12]. 18. Amazon: Lamp illuminates at 90,000 miles. Return vehicle to dealer.

download
Install the timing belt in this order: 1st: Crankshaft timing pulley 2nd: Water pump pulley 3rd: LH camshaft timing pulley 4th: NO. 2 idler pulley 5th: RH camshaft timing pulley 6th: NO. 1 idler pulley CAUTION: Incorrect removal or installation of the timing belt can result in damage to internal engine components. For complete Timing Belt Removal and Installation information, please refer to Timing Belt; Service and Repair. See: Timing Belt/Service and Repair