Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Replacement Interval Guide Toyota recommend: 1993: Replacement every 60,000 miles or 5 years, whichever occurs first. 1994 : Replacement every 63,000 miles or 5 years, whichever occurs first. 1996 : Replacement every 60,000 miles or 5 years, whichever occurs first (Colorado only). The previous use and service history of the vehicle must always be taken into account. Check For Engine Damage Check For Engine Damage Removal Removal 1. Remove timing belt cover [1]. 2. Turn crankshaft clockwise until timing marks aligned [2]. 3. Ensure timing marks aligned: 1KZ-T/TE: [3]. 1HD-FT/1HD-FTE: [4]. 4. Evenly slacken and remove automatic tensioner unit bolts [5]. 5. Remove: Automatic tensioner unit [6]. Tensioner pulley bolt [7]. Tensioner pulley [8]. Timing belt. Installation Installation 1. 2. 3. 4. 5. 6. 7. Check tensioner pulley for smooth operation [8]. Replace if necessary. Remove dust cover. Check tensioner body for leakage or damage [6]. Check pushrod protrusion is 9,0-9,8 mm [9]. Check pushrod does not move when pushed against a firm surface. If pushrod moves: Replace automatic tensioner unit. Slowly compress pushrod into tensioner body until holes aligned. Use press. Retain pushrod with 1,5 mm Allen key through hole in tensioner body [10]. Fit dust cover. Ensure timing marks aligned [2]. Ensure timing marks aligned: 1KZ-T/TE: [3]. 1HD-FT/1HD-FTE: [4]. 8. 9. 10. 11. 12. 13. 14. 15. 16. Fit timing belt in anti-clockwise direction, starting at lower sprocket. Ensure belt is taut between sprockets. Fit tensioner pulley [8]. Tighten bolt to 34 Nm [7]. Push tensioner pulley against belt. Install automatic tensioner unit [6]. Tighten bolts evenly to 13 Nm [5]. Remove Allen key from tensioner body to release pushrod. Turn crankshaft two turns clockwise. Ensure timing marks aligned [2] & [3] or [4]. If not: Repeat installation and tensioning procedures. Install components in reverse order of removal. Reset timing belt replacement warning lamp as follows: -Runner/Landcruiser: Remove grommet in speedometer housing. Depress switch using a thin screwdriver [11]. 17. Colorado: Remove speedometer housing. Remove screw indicated and insert in alternative location [12]. 18. Amazon: Lamp illuminates at 90,000 miles. Return vehicle to dealer.

download
IGNITION TIMING: Tachometer Hookup Start engine and allow to reach normal operating temperature.
1.Connect a tachometer test probe to terminal IG of the check connector, Fig. 211 2.NOTE: Never let the tachometer lead touch ground as this could cause damage to the igniter and/or coil. Be sure to check that your tachometer is compatible with this ignition system. Consult the operating manual for your instrument. Service Check Connector

Toyota SUPRA Sports Car Service Manual
From 1986-1998
Toyota SUPRA Turbo Non Turbo MKIII MKIV Service Manual

Toyota Celica-Supra 1986-1990 Repair Manual provides service, repair and maintenance information for 1986-90 Toyota Celica and Supra vehicles.

download
NOTICE: Always turn the crankshaft clockwise. (c) Check that the timing marks of the camshaft timing pul- leys and No.3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°). (d) Remove the crankshaft pulley bolt. IF REUSING TIMING BELT, CHECK INSTALLATION MARKS ON TIMING BELT Check that there are 3 installation marks and front mark on the timing belt. If the installation and front marks have disappeared, before re- moving the timing belt, place 3 new installation marks on the timing belt to match the timing marks of the timing pulleys, and place a new front mark on the timing belt. 18. 19. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt ten- sioner and dust boot. 20. REMOVE TIMING BELT 21. (a) REMOVE RH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 22. (a) REMOVE LH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 23. REMOVE NO.2 IDLER PULLEY Remove the bolt and idler pulley. 24. REMOVE NO.1 IDLER PULLEY Using a 10 mm hexagon wrench, remove the pivot bolt, idler pulley and plate washer. 25. REMOVE CRANKSHAFT TIMING PULLEY Remove the timing pulley. HINT: If the pulley cannot be removed by hand, use SST and a service bolt to remove the timing pulley. SST 09950–50011 (09951–05010, 09952–05010, 09953–05020, 09954–05011)