tsb 2005 chevrolet equinox WITH CODE P1791
You are searching repair manual in PDF format about tsb 2005 chevrolet equinox WITH CODE P1791 use another keyword for search another post or files
tsb 2005 chevrolet equinox WITH CODE P1791 Direct Download speed 5787 Kb/s
tsb 2005 chevrolet equinox WITH CODE P1791 Full Version speed 6767 Kb/s
Filed Under (Chevrolet) by admin on 01-01-2011
SUBJECT: MODELS: Loss of Power Steering Assist – Replace Electric Power Steering Motor 2005-2010 Chevrolet Cobalt 2005 Pontiac Pursuit 2005-2006 Pontiac G4 2006 Pontiac G5 Pursuit 2007-2010 Pontiac G5 Equipped with Electric Power Steering 2005-2010 model year Chevrolet Cobalt vehicles; 2005 model year Pontiac Pursuit; 2005-2006 model year Pontiac G4; 2006 model year Pontiac G5 Pursuit; and 2007-2010 model year Pontiac G5 vehicles equipped with electric power steering. Some of these vehicles have a condition in which a sudden loss of power steering assist could occur at any time while driving the vehicle. If the power steering assist is lost, a chime will sound and a “Power Steering” message will be displayed in the Driver Information Center to inform the driver of the condition. Steering control will be maintained, as the vehicle defaults to a manual steering mode. If power steering assist is lost, it may require greater driver effort at low vehicle speeds, for example, below 15 mph (25 km/h). Unless a driver compensates for this additional effort, it may increase the risk of a crash. Typically, the next time the vehicle is started, the power steering assist will return and the “Power Steering” message will no longer be displayed. EPS Motor Replacement Procedure Note: The use of Loctite is no longer required. Loctite should not be used for any further applications. 1. Connect the Tech 2® to the vehicle and check for diagnostic trouble codes (DTCs). 2. Record any present DTCs on the repair order and during claim submission. 3. Clear any DTCs that are present. 4. Remove the power steering assist motor. Refer to Power Steering Assist Motor Replacement in SI. Note: For 2005 model year vehicles only: Do NOT install the o-ring between the motor assembly and the steering column assembly. The new service motor kit will include an o- ring, but DO NOT install the o-ring for 2005 model year vehicles only. 5. Install the new power steering assist motor. Refer to Power Steering Assist Motor Replacement in SI. 6. Perform Test Drive.
Filed Under (Ford) by admin on 27-04-2010
ISSUE Some 2001-2005 Taurus/Sable, 2001-2006 Escape and 2005-2006 Mariner vehicles built prior to
1-17-2006 equipped with the 3.0L 4V Duratec engine may exhibit a ticking noise from the left bank cylinder head, with the engine at normal operating temperature only.
ACTION To diagnose, with the engine running and warm (normal operation temperature), using a mechanic’s stethoscope determine if the ticking noise is coming from the left hand intake camshaft at cylinder number 6, (Figure 1). If the ticking noise can be verified, refer to the following Service Procedure.
Filed Under (Buick) by admin on 24-12-2010
Subject: L36, L67, L26, L32, LA1, LX9, MN7, M15 Ticking or Knocking Type Noise Coming From Engine or Transmission Area (Replace Flexplate and Torque Converter) Models: 2005 Buick Park Avenue 2005-2006 Buick Allure (Canada Only), LaCrosse, LeSabre, Rendezvous, Terraza 2005 Chevrolet Impala, Monte Carlo, Venture 2005-2006 Chevrolet Malibu, Malibu Maxx, Uplander 2005 Pontiac Aztek, Bonneville 2005-2006 Pontiac Grand Prix, G6 GTP, Montana SV6 2006 Saturn Relay AWD with 3800 3.8L Series III V6 Engine (VINs K, 1, 2, 4, – RPOs L36, L67, L26, L32) or 3500 3.5L V6 Engine (VINs L, 8 RPO LX9) or 3400 3.4L V6 Engine (VIN E – RPO LA1) and Hydra- Matic(R) 4T65-E Transmission (RPOs MN7, M15) Some customers may comment on a ticking or knocking type noise coming from the engine or transmission area. Cause Typically the noise is caused by either the transmission rear dust cover contacting the flexplate (refer to Corporate Bulletin Number 05-06-01-028) or a cracked flexplate (sometimes also referred to as a flywheel). Correction With the vehicle raised and supported on a suitable hoist, verify that the noise is coming from the flexplate area. If the noise is present, follow the procedure below. If the noise is not coming from the flexplate area, refer to Lower Engine Noise, Regardless of Engine Speed in SI. Important: The following information only applies to vehicles with the noise coming from the flexplate area.
Filed Under (Ford) by admin on 07-09-2010
FORD: 2000-2004 Mustang 2000-2005 Crown Victoria, Taurus 2000-2003 Explorer Sport, Windstar 2000-2004 Ranger 2000-2005 E-Series, Excursion, Expedition, Explorer, F-150, F-Super Duty 2001-2005 Escape, Explorer Sport Trac 2004-2005 Freestar 2005 Escape Hybrid 2004-2005 F-650, F-750 LINCOLN: 2000-2002 Continental 2000-2005 LS, Town Car, Navigator 2003-2005 Aviator MERCURY: 2000-2005 Grand Marquis, Sable, Mountaineer 2004-2005 Monterey 2005 Mariner ISSUE A service kit is now available to improve safety belt retraction speed. ACTION See the part application chart and select the appropriate kit. Follow the Instruction Sheet included in the kit. Refer to Workshop Manual Section 501-20a for additional information. NOTE IF TEFLON TAPE IS ALREADY PRESENT ON THE SAFETY BELT GUIDE RING (D-RING), DO NOT CONTINUE WITH THIS TSB. NOTE EACH KIT SERVICES TWO (2) BELTS. NOTE DOES NOT APPLY TO AVIATOR/EXPLORER 4DR/MOUNTAINEER FRONT SAFETY BELTS FOR VEHICLES BUILT AFTER 6/25/2004, OR REAR SAFETY BELTS FOR VEHICLES BUILT AFTER 10/22/2004, BECAUSE TEFLON TAPE IS INSTALLED DURING PRODUCTION.
Filed Under (Ford) by admin on 14-08-2010
NOTE: Ford DOES NOT provide procedures to retrieve or clear trouble codes without the Super Star II tester. The anti-lock brake/traction assist system has on-board diagnostic capabilities. However, the module as received from manufacturing is equipped with a stored error code (61). This will affect the service procedure. The error codes can be retrieved from the ABS module in the following manner. 1. 2. 3. 4. Connect Super STAR II tester to connector located in engine compartment on the power distribution box. Turn on Super STAR II tester and latch button down in TEST position. Turn ignition switch to RUN position. Read first code output. After approximately 15 seconds, the next code will be output. Leave button latched until all codes are output. NOTE: Make sure that all codes are written down. 5. The diagnostic procedure should be as follows provided that the CHECK ANTI-LOCK BRAKE indicator stays on all the time or flashes intermittently. NOTE: If the BRAKE warning indicator is on or intermittently comes on, refer to the Warning Indicator Symptom Chart. NOTE: If there are more codes stored in the anti-lock brake control module memory, no codes will erase until all codes have been output by the Super STAR II tester, all malfunctions have been serviced and the vehicle is driven about 40 km/h (25 mph). This means that if a 20s code originally existed and was serviced, it can be ignored when running the on-board diagnostic the second time. If the first code received is 18, 19 or in the 20s and no other code is received, service the indicated component. No other codes can be output if a 20s code exists. After servicing the indicated 18, 19, or 20s code, repeat the procedure for retrieving error codes. 6. If a code 61 is received with any other code, ignore the code 61 and service the other indicated components. If, after correcting all other indicated malfunctions, the CHECK ANTI-LOCK BRAKE indicator is still on, service the Fluid Level Switch (FLS) circuit. 7. If a code 61 is received and no other codes are received, service the FLS circuit. 8. If no code, or only a code 10 is received, use the Anti-Lock Quick Check Sheet since some possibilities are not recognized and retained in the anti-lock brake control module memory. See: Trouble Code Descriptions/Quick Check Sheet 9. When dealing with intermittent ABS warning light ON concern, make certain to visually inspect all wiring related to the component associated with the code received.