vauxhall zafira brake diagram


You are searching repair manual in PDF format about vauxhall zafira brake diagram use another keyword for search another post or files



  vauxhall zafira brake diagram Direct Download speed 5787 Kb/s

  vauxhall zafira brake diagram Full Version speed 6767 Kb/s




2003 Ford Mustang Brake System Bleeding

0

Filed Under (Ford) by admin on 08-03-2011

download
Master Cylinder Priming — In-Vehicle or Bench WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in personal injury. CAUTION: Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. NOTE: When any part of the hydraulic system has been disconnected for repair or installation of new components, air can enter the system and cause spongy brake pedal (2455) action. This requires bleeding of the hydraulic system after it has been correctly connected. The hydraulic system can be bled manually or with pressure bleeding equipment. NOTE: When a new brake master cylinder (2140) has been installed or the system has been emptied, or partially emptied, it should be primed to prevent air from entering the system. 1. For in-vehicle priming, disconnect the brake lines. 2. For bench priming, mount the brake master cylinder (2140) in a vise. 3. Install short brake tubes with the ends submerged in the brake master cylinder reservoir (2K478), and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A. 4. Have an assistant pump the brake pedal (2455), or slowly depress the primary piston until clear fluid flows from both brake tubes, without air bubbles. 5. If the brake master cylinder has been primed at the bench, install it in the vehicle. For additional information, refer to Section 206-06. 6. Remove the short brake tubes, and install the brake outlet tubes. 7. Bleed each brake tube at the brake master cylinder as follows: 1. Have an assistant pump the brake pedal, and then hold firm pressure on the brake pedal. 2. Loosen the rear most brake tube fittings until a stream of brake fluid comes out. While the assistant maintains pressure on the brake pedal, tighten the brake tube fitting. 3. Repeat this operation until clear, bubble-free fluid comes out. 4. Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube. Master Cylinder Priming — 4.6L 1. CAUTION: Use only bleed screws on the engine side of the brake master cylinder (2140). The hydro-boost bleed screw, located near the dash on the hydro-booster casting, is for the booster cavity filled with power steering fluid, not brake fluid. Connect a clear waste line to the bleed screw closet to the booster first and the other end in a container partially filled with recommended brake fluid.

Related entry:

international 4300 brake bleeding, 2002 chevy 1500 brake line diagram, 2002 Cavalier Brakes Diagrams, gear pedal thread direction for sportster, 2004 explorer front brake diagram, bleedbrakefluid1997jimmy, diagrams of front brake caliprron 2005 trailblazer, brake line routing on a 1999 cadillac deville, how do you change the emergency brake cable on a ford 2005 super duty 4x4, how do you bleed the brake booster on a 2003 ford f550,

2000 Ford F-150 Parking Brake Rear Drum Brakes

0

Filed Under (Ford) by admin on 02-02-2011

download
Remote release handle Parking brake control Parking brake rear cable and conduit clip (part of 2A635) Parking brake cable bracket Parking brake rear cable and conduit— (LH) Parking brake rear cable and conduit— (RH) Parking brake cable equalizer Front parking brake cable and conduit Front parking brake cable clip The parking brake system is actuated when the parking brake control (2780) is depressed. The parking brake control applies tension to the front parking brake cable and conduit (2853) and parking brake cable equalizer (2A602). The parking brake cable equalizer is coupled to the RH parking brake rear cable and conduit (2A635) and the LH parking brake rear cable and conduit. The respective rear brake assemblies are then applied. The rear wheel brake assembly contains a cable-actuated parking brake assembly. The parking brake releases the rear brakes using a remote release lever incorporated with the parking brake control. If the parking brake control is not fully released, the parking brake signal switch will illuminate the brake warning light. The parking brake signal switch is mounted on the parking brake control. The switch is held in place by a self-tapping screw and aligned with a locater pin. The drum brake parking brake system is self-adjusting, therefore cable tension does not need to be adjusted. Rear Disc Brakes Parking Brake Components, Rear Disc Brakes

Related entry:

abs code co235 for 2000 chevy astro awd, e38 parking brake release assembly diagram, 2004 ford f250 brake line diagram, park brake light on solid ml350, 2006 cobalt rear brake manual, hand brake switch on berlingo van 2001 where is it located, 2008 honda accord brake torque spec, 2011 ford escape rear drum brakes, diagram for rear brakes for 2006 chevy equinox, adjusting the parking brake cable on 2008 hyundai tucson,

2008 Ford Expedition Brake Pads REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 04-03-2011

download
WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. WARNING: Always install new brake shoes or pads at both ends of an axle to reduce the possibility of brakes pulling vehicle to one side. Failure to follow this instruction may result in uneven braking and serious personal injury. NOTICE: Do not spill brake fluid onto painted or plastic surfaces or damage to surface may occur. If brake fluid is spilled onto a painted or plastic surface, immediately wash the surface with water. 1. Check the brake fluid level in the brake master cylinder reservoir. If required, remove the fluid until the brake master cylinder reservoir is half full. 2. Remove the wheel and tire. For additional information, refer to Section 204-04. 3. NOTICE: Do not allow the brake caliper to hang by the flexible brake hose or damage to the hose may occur. Remove the 2 brake caliper guide pin caps and bolts and position the caliper and brake pad assembly aside. Support the caliper using mechanic’s wire. Remove and discard the guide pin bushings. Inspect the guide pin threads for damage, install new guide pin(s) as necessary. 4. Remove the brake pads from the caliper. 5. Inspect the brake pads for wear or contamination and install new pads as necessary. For additional information, refer to General Procedures in Section 206-00. 6. Using a C-clamp and a worn brake pad, press the piston into the caliper. 7. Inspect the brake disc and resurface or install a new brake disc as necessary. For additional information, refer to General Procedures in Section 206-00. Installation 1. Clean, dry and inspect the brake caliper anchor plate. Apply equal amounts of the supplied yellow lubricant to the 4 brake pad contact points on the anchor plate as shown. 2. NOTICE: Do not apply lubricant to guide pin threads or incorrect tightening of the guide pins may result. Install new brake hardware as follows: Apply equal amounts of the supplied white lubricant to the inside of the guide pin bushings. Install the guide pin bushings into the caliper bores. Install the guide pins into the bushings. 3. Install the brake pads to the caliper. 4. Position the caliper onto the anchor plate and install the 2 brake caliper guide pin bolts. To install, tighten to 38 Nm (28 lb-ft). Clean and dry guide pin threads as necessary. 5. Fill the master cylinder with clean, specified brake fluid. 6. Install the wheel and tire. For additional information, refer to Section 204-04. 7. Apply the brake several times to verify correct brake operation.

Related entry:

07 colorado rotor replacement diagram, replace pressure hydro block for peugeot 206, installing rear caliper 2009 caravan or town and country, how to replace front brakes on 1990 chevy 1500, how to replace brake switch 2008 kia optima, how to change rear drum brakes shoe on 2008 dodge caliber, how to change rear brake pads on a peugot 2006, colbalt brake pin which pin goes on top, change rear break pads 2009 town and country, c65 gmc 1975 brake system how to bleed,

2007 Volkswagen Rabbit Brake pads removing and installing

0

Filed Under (volkswagen) by admin on 02-12-2010

download
Brake pads, removing When removing, mark brake pads that will be used again. Install in the same position, otherwise braking effect will be uneven! Remove wheels. Disconnect connector – 1 – for brake pad wear indicator. Remove caps – arrows -. Loosen both guide pins – arrows – and remove from brake caliper. Remove brake caliper and secure with wire so that the weight of the brake caliper does not burden or damage the brake hose. Remove brake pads from brake caliper. Cleaning: CAUTION: Do not blow brake system using compressed air, the dust produced is harmful to health! Thoroughly clean contact surfaces for brake pads at brake carrier, remove corrosion. Clean brake caliper. Use only appropriate solvents for cleaning brake caliper. Brake pads, installing Before pressing piston into cylinder using piston resetting tool, brake fluid must be extracted from brake fluid reservoir. Otherwise, especially if reservoir has been topped off, fluid will overflow and cause damage. Insert inner brake pad (piston side) – 1 – and outer brake pad – 2 – with retaining springs into brake caliper. Inner brake pad (piston side) with large three-finger clip – 1 -. Outer brake pad with small three-finger clip – 2 – (colored black). Place brake caliper with brake pads on brake carrier first at bottom – arrow -.

Related entry:

utube how to change front disk brakes on 2007 kia sorento, brake pad indicater inside or outside, thermo quiet pad wear indicator inner 2000 f150, renault trafic 2010 cheange break pads-video, new brake pads for a 2002 town & country, utube how to change front disk brakes on 2007 kia soreno, kia 2007 sorento brake pads installation instructions, inner brake assy bolt size 2007 equinox, how to install rear brake pads in a 2007 hyundai tucson, how to change the rear pads on a 2007 mercury Milan,

1998 Ford Expedition Master Cylinder Bleeding PROCEDURES

0

Filed Under (Ford) by admin on 28-03-2011

download
Master Cylinder, In Vehicle WARNING: Brake fluid contains polyglycol ethers and polyglycols. Avoid contact with eyes. Wash hands thoroughly after handling. If brake fluid contacts eyes, flush eyes with running water for 15 minutes. Get medical attention if irritation persists. If taken internally, drink water and induce vomiting. Get medical attention immediately. CAUTION: Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. NOTE: When any part of the hydraulic system has been disconnected for repair or new installation, air may get into the system and cause spongy brake pedal action. This requires bleeding of the hydraulic system after it has been correctly connected. The hydraulic system can be bled manually or with pressure bleeding equipment. 1. NOTE: When a new brake master cylinder has been installed or the system has been emptied, or partially emptied, it should be primed to prevent air from getting into the system. Disconnect the brake master cylinder outlet tubes. 2. Install short brake tubes with ends submerged in the brake master cylinder reservoir and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ- 19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A. 3. Have an assistant pump the brake pedal until clear fluid flows from both brake tubes without air bubbles. 4. Remove the short brake tubes and install the brake outlet tubes. 5. Bleed each brake tube at the brake master cylinder as follows: 1. Have an assistant pump the brake pedal and then hold firm pressure on the brake pedal. 2. Loosen the rearmost brake tube fittings until a stream of brake fluid comes out. Have an assistant maintain pressure on the brake pedal while tightening the brake tube fitting. 3. Repeat this operation until clear, bubble-free fluid comes out. 4. Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube. 6. While the assistant maintains pressure on the brake pedal, tighten the brake tubes.