what is the removal procedure on a 2000 BMW 323Ci for rear hub carrier assembly


You are searching repair manual in PDF format about what is the removal procedure on a 2000 BMW 323Ci for rear hub carrier assembly use another keyword for search another post or files



  what is the removal procedure on a 2000 BMW 323Ci for rear hub carrier assembly Direct Download speed 5787 Kb/s

  what is the removal procedure on a 2000 BMW 323Ci for rear hub carrier assembly Full Version speed 6767 Kb/s




2004 Ford F-150 Rear Axle Differential Cover Axle Shaft Oil Seal and Rear Wheel Bearing REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 28-02-2011

download
1. With the vehicle in NEUTRAL, position on a hoist. For additional information, refer to Section 100-00. 2. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-00. 3. Remove the parts in the order indicated in the following illustration and table. 4. To install, reverse the removal procedure. 5. Fill the axle with the specified quantity of the specified lubricant. For additional information, refer to the Specifications in this section. Item 2: Rear Disc Brake Caliper Removal Note 1. CAUTION: Do not allow the caliper to hang from the brake hose. Provide a suitable support. Position the rear disc brake caliper aside. For additional information, refer to Section 206-00. Item 7: Differential Pinion Shaft Removal Note 1. Move the differential pinion shaft out far enough to remove the U-washers. Replace the shaft and install the lock bolt finger tight when U-washers are removed. Item 8: U-washer Removal Note 1. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers. 1. Push the axle shafts inboard. 2. Remove the U-washers. Item 10 and 11: Wheel Bearing Oil Seal and Axle Shaft Bearing Removal Note 1. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 8.8 inch rear axle, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. 2. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 9.75 inch and the 10.25 inch rear axles, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. Item 11: Axle Shaft Bearing Installation Note 1. For the 8.8 inch and the 9.75 inch rear axles, use the special tools to install the rear axle wheel bearing. 2. For the 10.25 inch rear axle, use the special tools shown to install the rear axle wheel bearing. Item 10: Wheel Bearing Oil Seal Installation Note 1. Use the special tools shown to install the rear wheel bearing oil seal. Item 8: U-washer Installation Note 1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers. 1. Position the two U-washers on the button end of the axle shafts. 2. Pull the axle shafts outward.

Related entry:

diagram of the rear traction of dodge grand caravan awd 3 8, 2004 ford explorer rear differential diagram, 2005 kia sorento drive mid shaft bearing replacement procedure, 2003 explorer rear cv removal, diagram for 2008 ford F-150 8 8 rearend, 2007 kia sportage rear hub removal, 2002 ford explorer rear differential diagram, pictures of how to remove rear wheel bearings from 2003 suzuki xl7, 1999 rodeo wheel seal change schematic, saturn wheel hub torque specs,

2006 Honda Civic Rear ABS Wheel Speed Sensor and O-Ring Inspection

0

Filed Under (Honda) by admin on 10-01-2011

download
During assembly, some wheel speed sensors may have been improperly installed and do not seal the hub assembly. Water may enter the hub assembly and damage the wheel bearing. In areas where road salt is used, the wheel bearings may corrode, which may cause the wheel to separate and fall off, increasing the risk of a crash. CORRECTIVE ACTION Inspect both rear ABS wheel speed sensors and their O-rings. If an ABS wheel speed sensor or O-ring is damaged, replace the damaged part and the hub bearing unit on that wheel. REPAIR PROCEDURE 1. 2. 3. 4. Raise the vehicle on a lift. Remove the rear wheels. Remove both rear ABS wheel speed sensors. Inspect the rear ABS wheel speed sensors and their O-rings. • If a rear ABS wheel speed sensor O-ring is damaged (cut, torn, pinched, or flattened), replace the O-ring and the corresponding rear hub bearing unit, then go to step 5. DAMAGED O-RINGS: O-ring is pinched. • If the rear ABS wheel speed sensor tip has any physical damage, remove the original sensor assembly, replace the corresponding rear hub bearing unit(s), and connect the new sensor’s wire harness. Then go to step 5. – Refer to page 18-34 (with disc brakes) or 18-36 (with drum brakes) of the 2006–07 Civic Service Manual, or – Online, enter keyword HUB, then select Rear Knuckle/Hub Bearing Unit Replacement from the list. O-ring is rolled out of the groove and flattened. -Refer to page 18-34 (with disc brakes) or 18-36 (with drum brakes) of the 2006–07 Civic Service Manual, or – Online, enter keyword HUB, then select Rear Knuckle/Hub Bearing Unit Replacement from the list. • If the rear ABS wheel speed sensors and their O-rings are OK, go to step 5. 5. Lubricate the ABS wheel speed sensor O-ring and the sensor hole in the knuckle with multi-purpose grease.

Related entry:

2005 explorer rear abs sensor, vw golf mk3 rear pivot arm bush repairs, avalanche rear speed sensor, 2006 escape wheel sensor ring replace, rover 45 anti-lock braking system reluctor ring, how to take off rear hub on 2007 camry, HOW TO REPLACE WIREHARNESS BUICK RENDEZVOUS ABS SPEED SENSOR, how to replace a rear hub on a chevy equinox, 04 hyundai gx350i axel knokle hub with bushing, how to change front wheelhub assassembly on 07 hyundai santa fe all wheel drive,

2000 BMW 323I Sport Wagon Check engine light is illuminated in dash

0

Filed Under (BMW) by admin on 14-06-2010

download
Vehicle Application: 1998 BMW 528I 2.8L 2000 BMW 528IT 2.8L 2002 BMW X5 3.0L, Eng Cfg L6, Eng Des 1999 BMW 528IT 2.8L, Eng Des M52TU M54 2000 BMW 323I Sport Wagon 2.5L Customer Concern: Check engine light is illuminated in dash. Tests/Procedures: 1. Compare the actual engine temperature, as read by an infrared or contact thermometer, to the temperature shown on the scan tool. 2. If the temperatures are comparable, replace the coolant thermostat. A leaking thermostat will delay warm-up and keep the engine from coming up to proper temperature for closed loop operation. Potential Causes: Thermostat

Related entry:

1997 bmw 740il dash board removal, 1999 323i fuse box diagram, fuse box 323i, head removal on 2000 323ci m52t, 97 bmw 328is dash lights, head removal on 2000 323ci m52tu, 00 323i maf data at idle, diagram relays under driver side dash 2000 chevy zr2, free 2000 bmw 323i repair manual, how much is a crank shaft pulley for a 2000 bmw 323i,

1995 Ford Thunderbird Spring REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 02-03-2011

download
Removal 1. Raise vehicle on hoist. Refer to Section 00-02. 2. Remove rear wheel and tire assembly. 3. Remove rear stabilizer bar link and bushing link nuts at both ends of rear stabilizer bar (5A772) . Rotate bar up and out of the way. 4. Disconnect parking brake rear cable and conduit (2A635) at rear disc brake caliper (2553) . 5. Install three Rotunda Spring Cages 086-00031 or equivalent to rear spring as follows: a. Install one spring cage without an adjuster link to the inboard side (the innermost “bend” of the rear spring (5560) ). b. Install two more spring cages, with adjusters, at 120 degree angles to the previously installed cage. Spring, Rear 6. Place a transmission jack or suitable stand under the rear suspension arm and bushing (5500) as far outboard as possible. 7. Support the rear wheel knuckle (5A969) assembly by wiring the rear suspension arm and bushing to the body. 8. Remove lower rear shock absorber mounting bolt, washer and nut. 9. NOTE: Rear suspension arm and bushing must not be lowered until pivot bolts are loose. Do not attempt to remove plastic cap on front pivot nut. Loosen both inboard pivot bolts on rear suspension arm and bushing . 10. Remove two bolts and nuts retaining rear suspension arm and bushing to rear wheel knuckle . 11. Lower the rear suspension arm and bushing by lowering jack. Ensure spring cages properly seat on rear spring as rear suspension arm and bushing is dropped. 12. Remove jack, lower rear suspension arm and bushing down fully by hand and remove rear spring with cages in place. 13. Remove rear spring center mounting insulators (5741) , if necessary. 14. If spring cages are to be removed for installation on rear spring , use Coil Spring Compressor D78P-5310-A or equivalent to compress rear spring and remove cages. Rear spring center mounting insulator should be installed on rear spring before installing rear spring in tool to prevent slipping of plates.

Related entry:

2004 Ford Explorer Differential Diagram, D40 differential diagrams, schematic drawing of 2002 ford explorer rear suspension, exploded view of 1888 corvette rear hub assembly, 2003 rendezvous knuckle bushing, replacing rear shocks absorber buick rendez vous 2005, how to replace front strut 2007 ford fusion, 2004 rear differential diagram, how to replace the rear interear lighr on 1998 vw passat, 2007 buick rendezvous rear knuckle bushing tool,

1997 Cadillac Catera Drive Axles, Bearings and Joints: Rear Suspension REMOVAL PROCEDURE

0

Filed Under (Cadillac) by admin on 25-08-2010

download
1. Raise and support the vehicle. 2. Remove the tire and wheel assembly. 3. Use the J 42066 and use a 1/2 inch breaker bar to counter hold the rear wheel hub. Important: DO NOT allow the drive shaft to hang freely. Suspend the drive shaft upward. 4. Remove the drive shaft bolts. 5. Remove the drive shaft from the rear wheel hub flange. 6. 7. 8. 9. Remove the brake pipe clip from the lower control arm. Remove the brake pipe from the lower control arm. Remove the rear brake caliper. Suspend the rear brake caliper. The brake system remains closed. 1. Raise and support the vehicle. 2. Remove the tire and wheel assembly. 3. Use the J 42066 and use a 1/2 inch breaker bar to counter hold the rear wheel hub. Important: DO NOT allow the drive shaft to hang freely. Suspend the drive shaft upward. 4. Remove the drive shaft bolts. 5. Remove the drive shaft from the rear wheel hub flange. 6. 7. 8. 9. Remove the brake pipe clip from the lower control arm. Remove the brake pipe from the lower control arm. Remove the rear brake caliper. Suspend the rear brake caliper. The brake system remains closed. 13. Attach the J 42094-2 and attach the J 42094-1 to the rear wheel hub flange to hold the rear wheel hub while removing the rear wheel hub nut. Use the drive shaft bolts if necessary.14. Remove the rear wheel hub nut. 15. Use the J 42094-10 as a spacer to attach the J 42094-4 to the J 42094-1 with the supplied three bolts.

Related entry:

2003 buick rendevouz tork tube, 4A169A Drive Shaft Center Support Bushing for 08 Ford Edge, buick rendezvous torque tube bearing, jeep grand cherokee torque specs on driveshaft,