where is shift solenoid 2001 a6


You are searching repair manual in PDF format about where is shift solenoid 2001 a6 use another keyword for search another post or files



  where is shift solenoid 2001 a6 Direct Download speed 5787 Kb/s

  where is shift solenoid 2001 a6 Full Version speed 6767 Kb/s




2002-2004 Isuzu Axiom A/T – Shift Lock Solenoid Replacement

0

Filed Under (Isuzu) by admin on 30-04-2011

download
TSB SB05-05-5004 Shift Lock Solenoid ISSUE DATE: MAY 2005 Affected Vehicles 2002-2004 Isuzu Axiom (UP) 1998-2004 Isuzu Rodeo (UE) and Rodeo Sport (UA) Service Information Use the following steps to remove and replace the Shift Lock Solenoid. Service Procedure 1. Access the Shift Lock Solenoid by removing the Center, Front, Rear Console Assemblies, Selector Lever Knob, and Cover Assembly. Refer to the Selector Lever section in the Service Manual. 2. Set parking brake, move Selector Lever to lowest gear, and remove the Shift Lock Cable. 3. Remove the two screws securing the Shift Lock Solenoid to the Selector Lever subassembly. Disconnect the Shift Lock Solenoid 2-pin connector. 4. Disconnect the 1-40 (Rodeo) or 1-3 (Axiom) six-pin connector and slide the female connector off bracket. Remove the Terminal Position Assurance (TPA) Lock from the connector. Locate the two blue wires in position 1 and 3 on the female connector. With appropriate tool (shown above), apply light pressure upward on the connector locking tab while gently pulling on the blue wire to release. Note :Never use force to remove a terminal from a connector. 5. Insert the two blues wires from the replacement Shift Lock Solenoid into the 1- 40 (Rodeo) or 1-3 (Axiom) female connector. It does not matter which blue wire is inserted into the 1 and 3 position. Gently tug the blue wires to make sure they are secure. NOTE :D iscard the extra 2-pin connector sub harness included with replacement Shift Lock Solenoid P/N 8-97181-068-2. 6. Reconnect the Shift Lock Solenoid 2-pin connector and reattach the two screws securing the Shift Lock Solenoid to the selector lever subassembly. 7. Reconnect the 1-40 (Rodeo) or 1-3 (Axiom) six-pin connector and slide the female connector onto the bracket. 8. Reinstall the Selector Lever Knob, Cover Assembly, Center, Front, and Rear Console Assemblies. Refer to the Selector Lever section in the Service Manual. 9. Check Shift Lock operation: a. With ignition key in “Lock” position, Selector lever should not move from “P” position. b. With ignition key in “ON” position and brake pedal depressed. Selector lever can be moved out of “P” position. c. Key can be removed only when turned to “LOCK” position and selector lever is in “P” position.

Related entry:

how to replace shift selonoid on 2008 suzuki forenza, replace thermastat in 2002 iszuu acsium, 99 sonata shift solinoids, transmission release switch 02 mercury sable, ford explorer shift interlock repair, is there a fuse for the shift lever button on 2007 impala, replacing mazda 3 shift solenoid, 2003 chevy avalanche third gear shift solenoid location, mitsubishi mirage 2001 tcc solenoid, hhr 06 gear shirt selector override,

2000 Jeep Wrangler SHIFT BOOT REMOVAL

0

Filed Under (Jeep) by admin on 23-07-2010

download
1. Using a trim stick C-4755 or equivalent, pry the shift boot from the bezel. 2. Using a small flat blade, pry the shift pattern insert from the shift knob. 3. Remove the nut attaching the shift knob to the shift lever (Fig. 7). 4. Remove the knob and slide the shift boot from the shift lever. INSTALLATION 1. Slide the shift boot over the shift lever. 2. Snap the shift boot into place in the center console. 3. Position the shift knob on the lever, install the nut and tighten to 34 N.m (25 ft.lbs.) . 4. Position the shift pattern insert on the knob and press into place.

Related entry:

202 Cavalier Automatic Shifter repirs how to, manual de shift kit 4l30e, linkage assembly for shifter on a 2002 jeep wrangler schematic, hummer h2 3 gear automatic transmission not shifting, how to adjust shift cable 1997 olds cutlass, 4wd shift actuator, 1993 toyota tercel 4 speed transmission linkage, 2006 suzuki xl7 2 7 touble shoot 2wd/4wd transfer case, 2004 elantra shift boot, 2001 cavalier auto trans console diagram,

2007 TOYOTA TUNDRA SPORT SHIFT KNOB installation

0

Filed Under (Toyota) by admin on 30-01-2011

download
1. Vehicle Preparation. (FJ Cruiser shown) (a) Vehicle must be on level ground and not on an incline/decline. (b) Fully engage the parking brake. (c) Remove the shift lock release cover. Save for re-use. (Fig. 1-1) (d) Push in the shift lock release button. (Fig. 1-2) (e) Place the shifter in lowest gear. (Fig. 1-3) 2. Remove OE Shift Knob. (a) Remove the OE shift knob by turning counter-clock-wise. (b) Discard the OE shift knob 3. Install the Shift Knob. (a) Install the shift knob by turning clock-wise. (1) When fully installed there should be a 1/2” +/- 3/32” (12mm +/- 2mm) gap between the bottom of the shift knob shaft and the shift gate top surface. (2) The “barrel” of the shift knob should be oriented across the vehicle. (3) Place the shift lever in “Park”. (4) Replace the shift lock release cover. (5) Clean the shift knob with a non-scratch cloth.

Related entry:

how to remove an automatic shift knob with button chrystler pacifica 2004, 2005 jaguar shift interlock release, chrysler pacifica shifter knob, how take out a automachanic shift nob chrysler pacifica 2004, how to change the shifter knob on a 2005 FX 4 f-150,

1999 Ford F-Super Duty 250-550 Automatic Transaxle/ Transmission Cable and Bracket Removal and Installation

0

Filed Under (Ford) by admin on 14-03-2011

download
1. NOTE: To prevent cable damage, do not apply force to the transmission shift cable assembly between the steering column shift tube bracket and the steering column bracket. Disconnect the transmission shift cable from the steering column. 1. Disconnect the transmission shift cable from the steering column shift tube lever. 2. Carefully lift the locking tab and disconnect the transmission shift cable from the steering column bracket. 2. Disconnect the cable push pin from the stud in the bulkhead. 3. Push the rubber grommet and transmission shift cable through the bulkhead. 4. Raise and support the vehicle. For additional information, refer to Section 100-02. 4R100 transmission 5. NOTE: To prevent shift cable assembly damage, do not apply force to the transmission shift cable between the manual control lever and the transmission shift cable bracket. Remove the transmission shift cable from the transmission. 1. Disconnect the transmission shift cable from the manual control lever. 2. Depress the lock tabs to release the transmission shift cable and disconnect the transmission shift cable from the transmission shift cable bracket. 6. Remove the shift cable bracket from the transmission. 1. Remove the bolts. 2. Remove the shift cable bracket. 7. To install, reverse the removal procedure. Adjust the shift cable. For additional information, refer to Cable and Bracket Adjustment—4.2L, 4.6L with 4R70W Transmission or Cable and Bracket Adjustment—5.4L, 6.8L, 7.3L Diesel With 4R100 Transmission in this section.

Related entry:

2000 corolla automatic shift linkage diagram, how to replace shifter cable 2008 dodge avenger, 2000 CHRYSLER COCORDE SHIFTER CABLE, middle cable on jeep cherokee auto shift, how to install transmission shifter cable on a 2003 ford f350 super duty, diagram shifter linkage on 95 ranger, saab 93 1999–2003 gear selector cable drawing, 2001 ford winstar shift linkage adjustment tab, 4r70w repair manual, how to remove gear shifter cable of a hyundai excel,

2001 Pontiac Grand Prix Shifter A/T: Service and Repair Shift Control Replacement Removal Procedure

0

Filed Under (Pontiac) by admin on 16-08-2010

download
1. Remove the horseshoe clip (1) from front of shift control knob, and remove knob. 2. Remove the Console Trim Plate. 3. Remove the console wiring harness. 4. Remove the console shift control wiring harness. 5. Remove the automatic transaxle range selector cable. 6. Remove the park/lock cable. 7. Remove the console shift control nuts. 8. Remove the console shift control. Installation Procedure 1. Install the console shift control. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the console shift control nuts. ^ Tighten the console shift control nuts to 24 Nm (18 ft. lbs.). 3. install the park/lock cable. 4. Install the automatic transaxle range selector cable. 5. Install the console shift control wiring harness. 6. Install the console wiring harness. 7. Install the Console Trim Plate. 8. Adjust the transaxle range selector cable.

Related entry:

2010 impala gear shift electrical plug,