wheres the radiator drain on a 2006 chevy equinox


You are searching repair manual in PDF format about wheres the radiator drain on a 2006 chevy equinox use another keyword for search another post or files



  wheres the radiator drain on a 2006 chevy equinox Direct Download speed 5787 Kb/s

  wheres the radiator drain on a 2006 chevy equinox Full Version speed 6767 Kb/s




2007 Chevy Equinox Transaxle Fluid Replacement Removal Procedure

0

Filed Under (Chevrolet) by admin on 04-07-2010

download
1. Raise and support the vehicle. Refer to Vehicle Lifting. 2. Remove the drain plug and drain fluid. Allow at least 5 minutes for the fluid to drain completely. 3. Remove the gasket from the drain plug and discard. Installation Procedure 1. Install the new gasket on the drain plug. Notice: Refer to Component Fastener Tightening Notice. 2. Install the drain plug. Tighten the drain plug to 40 N.m (30 lb ft). 3. Make sure vehicle is level. 4. Remove the fluid level indicator located behind the front transaxle mount. Notice: Do not remove the 3rd gear anchor band bolt located on top of the transmission for checking fluid or adding fluid. Removing the bolt will dislocate internal components and require the transmission to be removed from the vehicle and disassembled for repair. Important: Dexron(R)III automatic transmission fluid is not compatible with this transaxle. If Dexron(R)III ATF is used, transaxle failure will result. Refer to Sealers, Adhesives, and Lubricants. 5. Add approximately 3.1 L (3.3 Qt)

Related entry:

2005 Equinox Drive Shaft remove, how to recharge ac on 2011 chevy cruze, how to empty ac system on a 2005 chevy malibu, how do i replace the thermostat on a 2010 chevy equinox, adding refrigerant to 2011 chevy cruze, ac drain line 2009 chevy malibu, AC drain 2009 malibu, 2010 chevy malibu ac drain location, 2006 equinox fan relays location, 2005 Equinox Drive Shaft remove front how,

2003 Ford Explorer Radiator Cooling Fan and Shroud Removal

0

Filed Under (Ford) by admin on 18-02-2011

download
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-00. 2. If servicing the radiator lower fan shroud or the radiator, drain the cooling system. For additional information, refer to Cooling System Draining, Filling and Bleeding in this section. 3. Remove the parts in the order indicated in the following illustrations and tables. To remove individual parts, only carry out the listed steps: 4. To install, reverse the removal procedure. If servicing the radiator lower fan shroud or the radiator, fill and bleed the cooling system. For additional information, refer to Cooling System Draining, Filling and Bleeding in this section. Item 9: Lower Degas Bottle Hose Removal Note 1. Remove the lower degas bottle hose from the clip on the radiator lower fan shroud. Item 10: A/C Tube Removal Note 1. On 4.6L engines, detach the A/C tube from the retainers. Item 11: Transmission Cooler and A/C Tubes Removal Note 1. Disconnect the transmission cooler tubes. Remove the safety retainers from the transmission cooler tubes. Using the special tool, disconnect the quick coupler. If equipped, loosen and remove the screw clamp from the hose. 2. Remove the A/C tube brackets from the engine front cover. Item 12: Radiator Fan Shroud Screw Removal Note 1. Not all vehicles will have these radiator fan shroud screws. If vehicle is equipped with these screws, please discard them. Item 15: Cooling Fan Removal Note 1. CAUTION: Cardboard must be placed against the radiator when removing the cooling fan. Failure to follow these procedures can result in damage to the vehicle. Place a piece of cardboard against the radiator to prevent damage while removing the cooling fan. 2. Using the special tools, remove the fan blade and the clutch assembly. Item 17: Radiator Lower Fan Shroud Removal Note 1. Remove the power steering tube from the clip on the radiator lower fan shroud. Item 19: Radiator Bracket Bolt Removal Note 1. If necessary, remove the radiator brackets. Item 21: A/C Condenser Support Bracket Bolt Removal Note 1. If necessary, remove the condenser brackets. Item 22: Radiator Removal Note 1. NOTE: It will be necessary to lift the radiator assembly up off the mounts and set it on the frame in order to separate the A/C condenser from the radiator. NOTE: RH side shown, LH side similar. Remove the radiator up off the mounts and set it on the frame. 2. Remove the left inner air deflector from the A/C condenser.

Related entry:

how to jump a radiator on 2004 kia sedona, wire schematic 2006 vw jetta cooling, renault espace mk3 jd0 fan sensor, 2001 lincoln ls radiator and condenser assembly photos, 2001 impala engin cooling fan wire diagram, how to remove radiator in 2004 ford explorer, ravs4 radiator removal, how to remove radiator 2003 chevy venture 3 4, how to take coolant fan out of 2002 dodge intrepid, how to take a radiator out of my Jaguar 2001,

2004 Ford Explorer Radiator Cooling Fan and Shroud Removal

0

Filed Under (Ford) by admin on 22-02-2011

download
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-00. 2. If servicing the radiator, drain the cooling system. For additional information, refer to Cooling System Draining, Filling and Bleeding in this section. 3. Remove the parts in the order indicated in the following illustrations and tables. 4. To install, reverse the removal procedure. If servicing the radiator, fill the cooling system. For additional information, refer to Cooling System Draining, Filling and Bleeding in this section. Item 9: Lower Degas Bottle Hose Removal Note 1. Remove the lower degas bottle hose from the clip on the radiator lower fan shroud. Item 10: A/C Tube Removal Note 1. On 4.6L engines, detach the A/C tube from the retainers. Item 11: Transmission Cooler and A/C Tubes Removal Note 1. Disconnect the transmission cooler tubes. Remove the safety retainers from the transmission cooler tubes. Using the special tool, disconnect the quick coupler. If equipped, loosen and remove the screw clamp from the hose. 2. Remove the A/C tube brackets from the engine front cover. Item 12: Radiator Fan Shroud Screw Removal Note 1. Not all vehicles will have these radiator fan shroud screws. If vehicle is equipped with these screws, please discard them. Item 15: Cooling Fan Removal Note 1. CAUTION: Cardboard must be placed against the radiator when removing the cooling fan. Failure to follow these procedures can result in damage to the vehicle. Place a piece of cardboard against the radiator to prevent damage while removing the cooling fan. 2. Using the special tools, remove the fan blade and the clutch assembly. Item 17: Radiator Lower Fan Shroud Removal Note 1. Remove the power steering tube from the clip on the radiator lower fan shroud. Item 19: Radiator Bracket Bolt Removal Note 1. If necessary, remove the radiator brackets. Item 21: A/C Condenser Support Bracket Bolt Removal Note 1. If necessary, remove the condenser brackets. Item 22: Radiator Removal Note 1. NOTE: It will be necessary to lift the radiator assembly up off the mounts and set it on the frame in order to separate the A/C condenser from the radiator. NOTE: RH side shown, LH side similar. Remove the radiator up off the mounts and set it on the frame. 2. Remove the left inner air deflector from the A/C condenser. 3. Remove the right inner air deflector from the A/C condenser.

Related entry:

2004 jaguar x type radiator fan removal, buick enclave amplifier replacement, clean saturn outlook condenser, how to install condenser in 2004 trailblazer, how to remove the bumper of 2008 volkswagen touareg 2, how to remove the lower dash in a 1998 gmc 1500, o8 malibu condensor removal, video on installation of a/c condessor in a dodge dakota, w906 sprinter dash removal,

2006 Chevy Equinox Trim Panel Replacement – Rear Quarter Lower Removal Procedure

0

Filed Under (Chevrolet) by admin on 23-10-2010

download
1. Remove the rear sill plate. Refer to Door Sill Plate Replacement – Liftgate (See: Scuff Plate\Service and Repair\Removal and Replacement) . 2. Move the rear seat forward. 3. Remove the load floor. 4. Disconnect the cargo hooks in the rear side trim panel. 5. Remove the push pins from the side trim. 6. If necessary, remove the jack to access the driver side rear side trim panel. 7. Remove the rear side trim panel. Installation Procedure 1. Align the rear side trim panel. Snap the panel into place. 2. Install the push pins to the side trim. Notice: Refer to Fastener Notice in Cautions and Notices. 3. Install the cargo hooks. Tighten the cargo hooks to 25 N.m (18 lb ft). 4. Install the load floor. 5. Install the rear sill plate. Refer to Door Sill Plate Replacement – Liftgate (See: Scuff Plate\Service and Repair\Removal and Replacement) .

2002 Toyota 4 Runner Radiator Removal and Installation

0

Filed Under (Toyota) by admin on 13-07-2010

download
REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE RADIATOR GRILLE Remove the 7 clips and radiator grille. 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT RADIATOR RESERVOIR HOSE 5. DISCONNECT LOWER RADIATOR HOSE 6. REMOVE RADIATOR NO.2 FAN SHROUD 7. A/T: DISCONNECT OIL COOLER HOSES 8. REMOVE RADIATOR Remove the 4 bolts and the radiator. DISASSEMBLY 1. REMOVE NO.1 FAN SHROUD Remove the 4 bolts and No.1 fan shroud. 2. REMOVE RADIATOR SUPPORTS 3. REMOVE DRAIN PLUG ASSEMBLE SST SST 09230-01010 a. Install the claw to the overhaul handle, inserting it in the hole in part “A” as shown in the diagram. b. While gripping the handle, adjust the stopper bolt so that dimension “B” shown in the diagram is 0.2 – 0.3 mm (0.008 – 0.012 inch). NOTICE: If this adjustment is not done, the claw may be damaged. 5. UNCAULK LOCK PLATES Using SST to release the caulking, squeeze the handle until stopped by the stopper bolt. SST 09230-01010 6. REMOVE TANKS AND O-RINGS a. Lightly tap the radiator port (inlet or outlet) with a soft faced hammer, and remove the tank. b. Remove the O-ring. REASSEMBLY