windshield wiper fuse for kia sportage


You are searching repair manual in PDF format about windshield wiper fuse for kia sportage use another keyword for search another post or files



  windshield wiper fuse for kia sportage Direct Download speed 5787 Kb/s

  windshield wiper fuse for kia sportage Full Version speed 6767 Kb/s




2006-2008 Buick Lucerne Heated Windshield Washer Module Short Circuit – Add Wire Harness

0

Filed Under (Buick) by admin on 01-01-2011

download
SUBJECT: MODELS: Heated Windshield Washer Module Short Circuit – Add Wire Harness 2006-2008 model year Buick Lucerne; Cadillac DTS; HUMMER H2 vehicles; 2007- 2008 model year Cadillac Escalade, Escalade ESV, Escalade EXT; Chevrolet Avalanche, Silverado, Suburban, Tahoe; GMC Acadia, Sierra, Yukon, Yukon XL; Saturn OUTLOOK vehicles; and 2008 model year Buick Enclave vehicles equipped with a heated washer fluid system. A short circuit on the printed circuit board for the washer fluid heater may overheat the control-circuit ground wire. This may cause other electrical malfunctions, create an odor, or cause smoke. In rare cases, it may cause a fire. PARTS INFORMATION No parts are required to pull the heated windshield washer fuse. When wire harnesses are available for ordering, a revised bulletin with ordering information will be sent to dealers/retailers. SERVICE PROCEDURE Important: Until wire harnesses become available, the following procedure allows dealers/retailers to remove the heated windshield wiper fuse, disabling the system. 2007-2008 Cadillac Escalade, Escalade EXT, Escalade ESV, 2007-2008 Chevrolet Avalanche, Silverado (GMT900), Suburban, Tahoe, 2007-2008 GMC Sierra (GMT900), Yukon and Yukon XL 1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in SI. Important: The underhood fuse block is located in the engine compartment on the driver side of the vehicle. Refer to Underhood Fuse Block in the Owner’s Manual for fuse information. 2. Locate the underhood bussed electrical center (UBEC). 3. Remove the UBEC cover and locate the 60 amp heated windshield washer fuse. Important: Remove the two relays (1) next to the fuse to gain access to the fuse. 4. Remove the 60 amp heated windshield washer fuse (2) using needle-nose pliers. 5. Store the 60 amp heated windshield washer fuse in the glove compartment. 6. Install the two relays (1) removed in Step 4. 7. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in SI. 8. Test the operation of the windshield wiper system. 8.1 Ensure the wiper system functions in low and high positions. 8.2 Verify that the windshield wiper/washer switch functions. The windshield wiper system should provide wiper fluid to the windshield. 8.3 Ensure that the heated windshield washer fluid system has been disabled. • Verify that the heated windshield washer switch does NOT flash. 9. Secure the UBEC cover on the UBEC. 10. Close the hood.

2005 Toyota Tacoma WIPER RUBBER LH REPLACEMENT

0

Filed Under (Toyota) by admin on 30-07-2010

download
1. REMOVE FR WIPER BLADE LH a. Raise the front wiper blade to the position as shown in the illustration. b. Disengage the claw and remove the front wiper blade LH from the front wiper arm LH. NOTE: Do not bend the front wiper arm with the front wiper blade LH removed, as the arm tip could damage the windshield surface. 2. REMOVE WIPER RUBBER LH a. Remove the front wiper rubber LH from the front wiper blade. b. Remove the 2 wiper rubber backing plates from the wiper rubber LH. 3. INSTALL WIPER RUBBER LH a. Install the 2 wiper rubber backing plates onto the wiper rubber LH. NOTE: Be sure to install the wiper rubber backing plates in the correct direction. b. Install the wiper rubber LH so that the head part (Larger side) of the wiper rubber faces the arm axle side. NOTE: Push the front wiper blade into the grooves of the wiper rubber to engage them completely.

1994 Suzuki Swift WIPER/ WASHER SYSTEM

0

Filed Under (Suzuki) by admin on 15-06-2010

download
A 2-speed wiper motor with intermittent mode is standard on all models. A 3-speed wiper motor is optional on some models. Washer system uses a reservoir-mounted electric pump located in the engine compartment. A one-speed rear wiper/washer is optional. Rear wiper/washer switch is located on instrument panel, to right of steering column. Wiper switch has 2 positions, rear wiper ON or OFF. Washer and wiper switch has 3 positions, OFF, washer ON (depressed half way), or washer and wiper ON (fully depressed). Washer/wiper switch moves to OFF position when switch is released. TESTING NOTE: If wiper malfunctions or does not return to park position,check for blown fuse, faulty wiper motor, control switch or connections. If washer malfunctions, check for clogged hose or nozzle, faulty washer motor, control switch or wiring. FRONT WIPER MOTOR REAR WIPER MOTOR INTERMITTENT WIPER RELAY WIPER/WASHER SWITCH WIPER MOTOR BRUSH & COMMUTATOR REMOVAL & INSTALLATION WIPER MOTOR WIRING DIAGRAMS

2007 Honda CR-V Windshield Wipers Intermittently Do Not Park or Turn Off

0

Filed Under (Honda) by admin on 12-01-2011

download
SYMPTOM When the windshield wipers are turned off, they intermittently do not park at the correct location at the bottom of the windshield, or they continue to run. The symptom is usually more noticeable in colder weather; however, it is difficult to reproduce. If you have a vehicle that reportedly has this symptom, replace the windshield wiper motor cover plate. PROBABLE CAUSE The windshield wiper motor cover plate is faulty. CORRECTIVE ACTION Replace the windshield wiper motor cover plate. REPAIR PROCEDURE NOTE: This procedure is in an outline form that you can also use as a checklist for the repair. If you need more details on the item listed below, bookmark it in the appropriate service manual, or view it online. • Wiper Motor Replacement. 1. Open the hood. Remove the caps, the nuts, and the windshield wiper arms. 2. Remove the cowl covers. 3. Remove the bolts and the under-cowl panel. 4. Disconnect the 5P connector from the wiper motor, and remove the wiper linkage assembly (Civic; six bolts, CR-V; four bolts). Then remove the wiper motor. 5. Remove the four screws from the cover plate. CR-V shown/ Civic similar COVER PLATE (Pry off.) 6. Using a flat-tip screwdriver, partially pry up the cover, using the connector for leverage. Then partially pry up the opposite side using the screw boss for leverage. NOTE: Be careful not to damage the motor gear case. 7. Pull the cover straight off the motor case. NOTE: Be careful not to contaminate the internal coupler and gears butyl sealer, grease, or other debris. CR-V shown/ Civic similar 8. Using some grease from the original cover plate or the motor gear case, grease the new cover plate at the three locations shown. CR-V shown/ Civic similar

2007 Buick Terraza Rear Window Wiper Motor Replacement

0

Filed Under (Buick) by admin on 18-11-2010

download
1. Remove the rear wiper arm (5). 2. Remove the rear wiper motor drive shaft nut (6). 3. Remove the washer (7) and seal (8) from the wiper motor drive shaft. 4. 5. 6. 7. 8. Remove the liftgate trim panel. Disconnect the electrical connector (1) from the rear wiper motor. Remove the rear wiper motor screws. Remove the rear wiper motor (3) from the liftgate (5). Remove the rear wiper motor from the vehicle. Installation Procedure 1. Position the rear wiper motor (3) to the liftgate. Notice: refer to Fastener Notice. 2. Install the rear wiper motor screws. Tighten the screws to 6 N.m (53 lb in ). 3. Connect the electrical connector (1) to the wiper motor. 4. Install the washer (7) and seal (8) onto the rear wiper motor drive shaft. 5. Install the rear wiper motor drive shaft nut (6). Tighten the nut to 6 N.m (53 lb in ). 6. Install the rear wiper arm. 7. Inspect rear wiper for proper operation. 8. Install the liftgate trim panel.