Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
NOTE: When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage. Take care not to scratch the dashboard and related parts. 1. Remove the dashboard center lower cover (A). -1 Gently pull out the cover to release the clips and hooks (B). -2 If equipped, disconnect the accessory power socket connector (C) and seat heater switch connector (D). 2. Install the cover in the reverse order of removal, and if equipped, make sure the accessory power socket connector and seat heater switch connector are plugged in properly. Without BOSE Sound System NOTE: Put on gloves to protect your hands. Take care not to scratch the dashboard and related parts. 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the radio’s preset buttons. 2. Remove the dashboard center lower cover. 3. Remove the two mounting bolts, then remove the center panel. 4. Disconnect the audio unit connector (A), antenna lead (B) and hazard warning switch connector (C), then remove the audio unit (D).

download
Special Tools Required KTC trim tool set SOJATP2014* *Available through the American Honda Tool and Equipment Program; call 888-424-6857 NOTE: Take care not to scratch the front seat, dashboard, and related parts. Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. 1. M/T model: Remove the shift knob (A). -1 Lower the shift lever boot (B) to release the hooks (C) from the knob. 2. Detach the clips (A, B) by pulling the center console front panel (C) up. If equipped, disconnect the seat heater switch connectors (D). 3. Pry up on the right of the console pocket (A) with a trim tool, and detach the clips, then remove the pocket. 4. Remove the screws (A), detach the clips (B) and hook (C) by pulling the center holder (D) up, and disconnect the front accessory power socket connector (E). 5. Detach the clips (A, B) by pulling the center console rear panel (C) up. 6. Remove the center console (A). -1 Open the console box lid (B) then remove the console mat (C). -2 If equipped, disconnect the rear accessory power socket connector (D), and detach the clip (E). -3 Remove the screws (F, G), then pull the rear portion of the console up to release the hooks (H), then remove

download
Special Tools Required KTC trim tool set SOJATP2014 * * Available through the American Honda Tool and Equipment Program. NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage when removing components. Take care not to scratch the front seat, dashboard, and related parts. 1. Detach the clips (A, B), and release the hooks (C) by pulling the center console trim (D) from both sides. 2. Open the console box lid (A) then remove the console mat (B) and screws (C, D). 3. Slide the rear section of the center console (A) rearward to release the hooks (B). 4. Lift up the rear of the console (A). Release the harness retainer clip (B) from the air duct, and disconnect the console accessory power socket connector (C), the light bulb socket connector (D), and the AUX connector (E), then remove the rear section of the center console. 5. Install the console in the reverse order of removal, and note these items: Check if the clips are damaged or stress-whitened, and if necessary, replace them with new ones. Push the clips into place securely. Make sure the console accessory power socket connector and the AUX connector are plugged in properly, and the light bulb socket is connected securely.

download
CIGAR LIGHTER HOUSING OR 12 VOLT ACCESSORY POWER RECEPTACLE REPLACEMENT TOOLS REQUIRED J 42059 Cigar Lighter Socket Remover REMOVAL PROCEDURE 2. Remove the cigar lighter element. 3. Remove the cigar lighter housing by placing one side of the T portion of J 42059 into the tab window and the other side into the opposite tab window. Pull the lighter housing straight out. 4. Remove the tool from the lighter housing 5. Pull the housing (3) and the retainer (2) out of the ash tray. 6. Disconnect the electrical connector (1) from the housing. 7. Remove the retainer from the housing. INSTALLATION PROCEDURE 1. Install the cigar lighter retainer (1) to the ash tray, by pressing the retainer into place until fully seated. 2. Connect the electrical connector (2) to the retainer.

download
L/H Maxi-Fuse & Circuit Breaker Identification 1 – 50 Amp STRG 1-2 Retained Accessory Power (Radio/Wipers), Starter, Trunk Comp Fuses 8 & 9 2 – 60 Amp BODY Engine Comp Fuse 9, Road Sensing Suspension, Fog Lights, Trunk Comp Fuses 16, 17, 18, 19, 20 & 21 3 – 30 Amp Circuit Breaker SEAT Power seat switches, Lumbar Relays, Power Door Locks, Keyless Entry Module, Horns, Fuel Door/Trunk Release Switch 4 – 30 Amp IPC Powertrain Control Module, Electronic Climate Control, RAP/Illuminated Entry Module, Instrument panel Cluster, Pass-Key Decoder Module, Theft Deterrent 5 – 60 Amp HVAC L & R Heated Seats, Electronic Level Control, Deck Lid Pull Down, Power Antenna, Rear Defogger, Heated Mirrors 6 – 60 Amp STRG 3 Retained Accessory Power (Sunroof/Power Windows), Engine Comp Fuses 26, 27, & 28, Trunk Comp Fuses 3, 4, 5, 6, & 7