Filed Under (Acura) by admin on 23-08-2010
download
Never use an air hose or dry brush to clean brake assemblies. Use an OSHA-approved vacuum cleaner to avoid breathing brake dust . 1. Loosen the front wheel nuts slightly, then raise the vehicle and support if on safety stands. 2. Remove the caliper bolt, and pivot the caliper up out of the way. NOTE: Check the hoses and pin boots for damage or deterioration. 3. Remove the pad shim, pad retainers and pads. 4. Using vernier calipers, measure the thickness of each brake pad lining. The measurement does not include pad backing plate thickness. Brake Pad Thickness: Standard: Type R Model: 10.5 – 11.5 mm 10.41 – 0.45 inch) All except Type R Model: 9.5 – 10.5 mm (0.37 – 0.41 inch) Service Limit: 1.6 mm 10.06 inch) 5. If the brake pad thickness is less than the service limit, replace the front pads as a set. 6. Clean the caliper thoroughly; remove any rust, and check for grooves and cracks.
Filed Under (Acura) by admin on 03-11-2009
: Gauge bezel can be painted using a plastic safe paint. 1. Remove stock gauge bezel. 2. Acura Integra – Drill 7?64″ hole in the plastic cross member. Install aluminum bracket (Fig. 1). Bracket stud should align with hole in lower center of gauge bezel.
Honda Civic – Remove bottom center screw from gauge cluster housing. Reinstall screw and supplied aluminum bracket (Fig. 2). 3. Install gauges in new gauge bezel (gauges are press fit). 4. Install new gauge bezel using supplied screws in the top and bottom center of the new bezel to attach the bezel to the aluminum bracket. There are no clips on the new bezel. 5. Run gauge wiring out through the firewall
download
Filed Under (Acura, Ford, Honda) by admin on 01-11-2009
Page 1 CHART EXPLANATION B- 12 voltignition U- 12 volt battery E- ECU Ground P- Pressure sensor, Air flow signal
(Note: some applications have multiple “P” signals-Use P(AFR) for AFR and P(FCD) for FCD) I- RPM signal S- Speed Sensor T- Throttle Position Sensor
#- Injector Signal * ALL DIAGRAMS ARE SHOWN FROM THE WIRE SIDE OF THE HARNESS FORD FOCUS ZX3 2000-2003 2.0L ZETEC (DOHC)
ECU LOCATION-4 Hot Wire (0-5V) HONDA / ACURA ACURA RSX/HONDA CIVIC SI 2002-2004 K20A2 ECU LOCATION-3 Pressure Sensor Type HONDA CIVIC 1988-1991 ACURA INTEGRA 1986-1993
The following diagrams may differ slightly depending on vehicle year, or model (California or Federal). Confirm that the diagram shown
corresponds to your vehicle by referencing the factory repair manual. Locate the engine control unit (ECU) using the diagram below.
FORD FOCUS ZX3 2000-2003 2.0L ZETEC (DOHC) ECU HONDA / ACURA ACURA RSX/HONDA CIVIC SI 2002-2004
download
Filed Under (Acura, Honda) by admin on 13-10-2009
Turbo Kit Installation Instructions No. 60108-rev.b
IMPORTANT, READ THIS FIRST: Study these instructions completely before proceeding. Engine and/or turbocharger damage may occur if any component within these instructions is improperly installed. Turbonetics, Inc. or any of its distributors cannot be held responsible for damages as a result of negligent or improper installation. This complete turbocharger system can be installed using common tools and automotive procedures, but installer must have a thorough knowledge of automotive engine operation and feel comfortable working on the vehicle. If in doubt, consult a knowledgeable turbo installer or Turbonetics tech support specialist with any questions
download
