Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Fig.17 Center Dash Bezel. 1. Remove ash tray, then six center cluster bezel screws and center bezel. 2. Remove two screws holding dash pad located behind top of center bezel, then gently pry defroster grille out of dash pad. Fig.18 Dash Pad & Instrument Cluster. 3. 4. 5. 6. Disconnect sensors, if equipped, and set defroster grille aside. Remove four screws in defroster duct opening holding dash pad. Remove three screws above instrument panel cluster, then open glove box and remove two screws holding dash pad. Remove dash pad by pulling up to unsnap end clips. If dash switch pod removal is necessary, proceed as follows: a. Remove one screw from left side, near driver’s door, of the lower trim panel. b. Remove one screw from bottom of lower trim panel, then pull panel off. c. Remove four screws holding steering column cover, then three screws holding bottom of bezels. d. Remove two screws retaining top of end and switch pod bezels, then remove the bezel. e. Remove two screws holding left side of switch pod and three screws on the RH side of switch pod bezel. f. Pull switch pod bezel out to remove switch connectors, then disconnect connectors from each switch pod and remove bezel. g. Remove switch retaining screws, then the switch. 7. Remove three screws from top of cluster, then lift cluster up to allow access to connectors. 8. Disconnect connector and remove cluster. 9. Reverse procedure to install.

download
Control lockout override via grounding of unused e-brake input Rear camera input switch DISCLAIMER: Anyone following these instructions is doing so at their own risk and agrees to not hold me liable for any damage caused as a result of reproducing my experiences that I am documenting here for your reference only. PART 1: REMOVAL OF BEZEL Subaru’s instructions indicate that the bezel can be removed by hand. No one on any message board seems to be able to do this. The solution many have found is to use a trim removal tool. I bought a cheap one at Wal- Mart and quickly found that any small plastic chisel or rubber-coated screwdriver will do. The trick is to get just enough leverage using the tool from inside the vents to pop off the corners. Using your fingers just isn’t quite enough. As you can see, I did use a cheap trim removal tool, but found using the stubbier end worked better for me. Insert any kind of soft (plastic or rubber) tool with a thin edge into the vent and feel for the lip underneath. The hardest part is to get the willpower to give it a good, firm yank towards you. Every time I pulled off another section, I swore it was going to break in half.

download
Replacement Crash Pad Center Lower Tray Replacement 1. Remove the knob (A).2. Remove the console under cover (B). 3. Disconnect the connector (C). 4. After loosening the mounting screws, remove the center fascia lower panel (A). 5. Disconnect the connector (A). 6. After loosening the mounting screw, remove the upper center tray bezel (A). 7. After loosening the mounting screw, remove the lower tray (A).8. Installation is the reverse of removal. NOTE: Make sure the connector is plugged in properly. ?

download
Item Part Number 666C04 611D52 613C46 — 611B64 66600/66800 W504042 W505274 — 10 W701259 11 63518 12 613A38 13 — 14 62418 15 624A08 16 613A38 17 W506542 18 613F18 19 W504042 20 62178 Description Safety belt guide cover Foam, safety belt retractor cover Safety belt retractor cover Safety belt retractor guide (part of 611B64) Safety belt retractor Backrest trim cover/foam pad Safety belt retractor cover screws (2 required) Safety belt retractor bolt Backrest support panel screws (8 required) (part of 613A38) Pin-type retainers (2 required) Attaching straps (2 required) Backrest support panel Screws, release handle (2 required) Release handle Release handle bezel Backrest frame Backrest-to-cushion bolts (2 required) Pivot bolt Screw, pivot bolt cover Pivot bolt cover

download
Remove or Disconnect 1. 2. 3. 4. 5. 6. Inside handle bezel assembly. Front side door pull cup assembly. Window regulator handle, if equipped. Rearview mirror remote control (driver-side only). Trim panel screws. Trim panel by carefully prying off top of trim panel to release tabs from door inner panel. Push up and pull trim panel toward you to remove trim panel. Install or Connect 1. Rearview mirror remote control (driver-side only). 2. Position trim panel tabs and hooks to slots in door inner panel. 3. Trim panel by pressing down on top of trim panel. Important ^ Be sure to apply enough pressure to fully engage the three top tabs to the door inner panel. 4. Trim panel screws. Tighten ^ Screws to 1.9 N.m (17 lb. in.). 5. Window regulator handle, if equipped. 6. Front side door pull cup assembly. 7. Inside handle bezel assembly.