Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
WARNING! Disconnect battery Ground (GND) strap before working on electrical system, observing all cautions => Repair Manual; Electrical; Repair Group 27, Battery, disconnecting and reconnecting. Removing Note: Before disconnecting battery Ground (GND) strap obtain security code for radio with anti- theft coding. Remove driver’s airbag unit => page 69-50. Remove steering wheel => page 69-61. Note: For vehicles with steering angle sensor -G85- observe: => Suspension, Wheels, Steering; Repair Group 48 – Steering; Steering column, removing and installing; Sequence for vehicles with steering angle sensor -G85-. For vehicles without steering angle sensor -G85- observe: => Suspension, Wheels, Steering; Repair Group 48 – Steering; Steering column, removing and installing; For vehicles without steering angle sensor -G85-. Remove two screws -arrows-. Remove steering column switch upper trim -1-. Remove three screws -arrows-. Release steering wheel height adjustment -2-. Remove steering column switch lower trim-1-. Note: Handle for height adjustment can be removed (two screws) to ease removal of lower trim. Remove Hex socket (Allen key) head bolt -1-. Disconnect connectors -arrows- from steering column switches. Remove steering column switch. Remove screws -1-. Remove driver’s side footwell cover -2- from retainers -3-.

download
1. – Horn pad – Removing, Fig. 1 Horn plate – Removing, Fig. 2 50 ±10 Nm (37 ±7 ft lb) Steering wheel – Horn contact ring, Fig. 3 – Lubricate horn ring with universal grease Steering column switch securing screws Combination switch – Turn signal switch. -E2- – Headlight dimmer/flasher switch -E4- – Emergency flasher switch -E3- – Removing, Fig. 4 Windshield wiper/washer switch -E22- – Removing, Fig. 4 Upper steering column trim Lower steering column trim Steering column Support ring Steering lock housing securing bolt 2. – 3. – 4. – 5. – 6. – 7. – 8. 9. 10. 11. 12. – - – - – 2000 Volkswagen Cabrio L4-2.0L (ABA) – Shear bolt Steering lock housing – Removing and installing, refer to Steering and Suspension, Steering, Steering Column, Service and Repair Ignition/starter switch -D- – To remove, first remove steering lock housing, then remove securing screws Lock cylinder – Removing/installing, Fig. 5 Spring Clamping washer 13. – 14. – 15. – 16. – 17. – Fig. 1 Horn pad, removing WARNING! Vehicles with airbags, refer to Service Precautions Vehicles without airbag – Lift horn pad at bottom and pull from steering wheel in direction of arrow. – Remove horn wire. Fig. 2 Horn plate, removing – Remove wire connector from horn plate. – Disengage retaining lugs -arrows- and remove contact plate -A- from contact plate -B-. Note: The horn plate consists of two non insulated contact plates. Horn operates when the horn pad is pressed and plate -A- contacts plate -B- .

download
REMOVAL 1. Remove the covers over the heating/air-conditioning system, battery and fluid tank. Disconnect and remove the battery. 2. Remove the refrigerant by suction using the service unit. 3. Detach the air-conditioning lines at the expansion valve. Immediately close connections and lines with plugs so that they are air-tight. 4. Remove steering wheel and loosen steering column panel. Comply with safety regulations when handling airbag units (see SAFETY REGULATIONS FOR VEHICLES WITH AIRBAG AND BELT TENSIONER ). 5. Undo the central screw (clamp) on the steering column switch from below and pull it forwards slightly. Remove the cover at the top and disconnect the electrical plug connections. Remove the steering column switch.

download
Disconnect battery negative lead. Remove fixture for steering column switch. Remove center console. Remove trim for center console. Remove right glovebox. Remove all clip-fitted trims (on instrument panel). Remove carrier in center console. Remove both panels for front roof pillar. Remove light switch unit. Remove complete instrument carrier. Remove heating controls. If necessary, remove radio receiver. Remove airbag module on passenger side. If necessary, release screw (1).