Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
To prevent damage, ensure steering wfieel and spiral cable DO NOT rotate before or during reassembly. SRS warning lamp Airbag Operation • Switch ignition ON. a SRS warning lamp illuminates. D Lamp extinguishes after approximately 6 seconds. • If not: Refer to Self-diagnosis section. D SRS control module fault memory can only be checked using diagnostic equipment connected to the data link connector (DLC). Disarm the system /0\ ^ ^ ^ J ^ ^ ^ / When Fascia/instrument panel removal or replacement. Front seat belt removal or replacement. Front seat repair or replacement. Repair wor1< around SRS components, especially airbag and pretensioners. • SRS component removal or replacement. D Steering wheel/column repair or replacement. • Welding operations. • • • o How n Ensure ignition switched OFF. o Remove ignition key. • Disconnect battery earth lead. Make sure accidental reconnection is not possible. • Wait 10 minutes tiefore commencing work. Arm the system : ^ How n Ensure ignition switched OFF. D Reconnect battery earth lead. D Keep clear of deployment area. D Switcti ignition ON. • Check SRS warning lamp operation.

download
Replacing Low Beam Headlamp NOTE: Left Low Beam Headlamp M29 and Right Low Beam Headlamp M31 can be checked via output Diagnostic Test Mode (DTM) of Vehicle Electrical System Control Module J519. Removing: Switch off ignition and all electrical components and move ignition key or start button into position 0 (preliminary engaged position). NOTE: During removal and installation, leave ignition key with remote control inside the vehicle to prevent the doors from locking and possibly activating the “Coming Home / Leaving Home” functions on its own. In order to be able to replace low beam headlamp, it is sometimes necessary to remove neighboring components at the corresponding headlamp. Refer to the following tables to determine additional component removal as required, depending on engine. NOTE: Low beam headlamp bulb -2- is clipped into the reflector -1-. When removing low beam headlamp bulb – 2-, the harness connector – 3-is not disconnected first. Push harness connector and thereby the lamp socket in -direction of arrow- until the lamp can be felt as loose. Pull low beam headlamp at harness connector -3- out of reflector. Pull low beam headlamp -2- from harness connector -1-. Installing: NOTE: When installing cap, ensure proper seating. Water intrusion will damage headlamp. Do not touch the glass of the light bulb, when installing. Your fingers will leave traces of grease on the glass which, when the light is switched on, will evaporate and cloud the glass. Install in reverse order of removal, noting the following: Guide low beam headlamp into headlamp housing.

download
CAUTION: When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage. NOTE: Take care not to scratch the dashboard and related parts. Instrument panel: 1. Remove the center air vent. 2. Remove the climate control unit and audio unit as an assembly (’96 – 98 models, ‘99 – 04 models). NOTE: Do not disconnect the connectors. 3. Remove the dashboard lower cover and driver’s switch trim. 4. Remove the screws, detach the clips, then carefully pull out the instrument panel in the numbered sequence. Disconnect the connector, then remove it. NOTE: Release the adhesive at the left side of the skirt carefully. 5. Installation is the reverse of the removal procedure. NOTE: Make sure the connections are connected properly. Dashboard lower cover: Detach the clips, then remove the dashboard lower cover. Installation is the reverse of the removal procedure. Driver’s switch trim: 1. Remove the dashboard lower cover.

download
1. Remove in the order indicated in the table. 2. Install in the reverse order of removal. 3. After installation, inspect the front wheel alignment and adjust it if necessary. (See FRONT WHEEL ALIGNMENT ). Fig. 3: Wheel Hub/Steering Knuckle Components & Torque Specification LOCKNUT REMOVAL NOTE 1. Knock the crimped portion of the locknut outward using a small chisel and a hummer. 2. Lock the hub by applying the brakes. 3. Remove the locknut. Fig. 4: Knocking Crimped Portion Of Locknut Outward Using Small Chisel And Hummer BRAKE CALIPER REMOVAL NOTE 1. Remove the brake caliper component from the steering knuckle and suspend it out of the way using a cable. Fig. 5: Removing Brake Caliper WHEEL HUB, STEERING KNUCKLE COMPONENT REMOVAL NOTE 1. Separate the shock absorber from the wheel hub, steering knuckle component by tapping the upper part of the steering knuckle with a hammer.

download
Instrument panel: 1. Remove the center air vent. 2. Remove the climate control unit and audio unit as an assembly (’96 – 98 models, ‘99 – 04 models). NOTE: Do not disconnect the connectors. 3. Remove the dashboard lower cover and driver’s switch trim. 4. Remove the screws, detach the clips, then carefully pull out the instrument panel in the numbered sequence. Disconnect the connector, then remove it. NOTE: Release the adhesive at the left side of the skirt carefully. 5. Installation is the reverse of the removal procedure. NOTE: Make sure the connections are connected properly. Dashboard lower cover: Detach the clips, then remove the dashboard lower cover. Installation is the reverse of the removal procedure. Driver’s switch trim: 1. Remove the dashboard lower cover. Climate control unit and audio unit (’96 – 98 models):