Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Special Tool(s) Safety Belt Bolt Bit 501-010 (T77L-2100-A) Windshield and Molding/Trim Removal Kit or equivalent 107-R0401 Removal 1. If equipped, remove the retractable cargo cover. 2. Remove the liftgate scuff plate (13144). 1. Starting at either end and working along the liftgate scuff plate, use Windshield and Molding/Trim Removal Kit to remove the scuff plate. 2. Remove the liftgate scuff plate. 3. If equipped, remove the rear power lock switch assembly. Disconnect the electrical connector. 4. Remove the B-pillar trim panel. For additional information, refer to Trim Panel—B-Pillar. 5. Remove the three rear quarter trim panel screws. Position the carpet aside to gain access to the screws. 6. Remove the rear safety belt anchor nut. 7. Open the rear safety belt guide bolt cover. 8. Using the special tool, remove the rear safety belt guide bolt. 9. Remove the quarter trim panel (31012). 1. Remove the pin-type retainers. 2. Feed the safety belt webbing through the opening in the quarter trim panel. 3. Remove the quarter trim panel. Installation 1. Install the quarter trim panel. 1. Feed the safety belt webbing through the opening in the quarter trim panel. 2. Position the quarter trim panel. 3. Install the pin-type retainers. 2. Using the special tool, install the rear safety belt guide bolt. 3. Close the rear safety belt guide bolt cover 4. Install the rear safety belt anchor nut. 5. Install the three rear quarter trim panel screws. 6. Install the B-pillar trim panel. For additional information, refer to Trim Panel—B-Pillar. 7. Install the liftgate scuff plate. 1. Position the liftgate scuff plate. 2. Start at either end and work along the liftgate scuff plate, pushing it into the floor panel. 8. If equipped, install the retractable cargo cover.

download
1. Recover the refrigerant. For additional information, refer to Section 412-00. 2. If equipped with a 5.0L or 4.0L SOHC engine, disconnect the condenser to evaporator tube (19835) from the A/C condenser core (19712). 3. If equipped with a 4.0L push rod engine, disconnect the condenser to evaporator tube spring lock couplings from the A/C condenser core. For additional information, refer to Section 412-00. 4. Disconnect the condenser to evaporator tube spring lock coupling from the A/C evaporator core (19860) and remove the condenser to evaporator tube. For additional information, refer to Section 412-00. Installation 1. To install, reverse the removal procedure.

download
Latch—Door Removal and Installation NOTE: Front door shown, rear door similar. Front door 1. Remove the door lock cylinder; refer to Lock Cylinder—Door. 2. If equipped, remove the power door lock actuator. 1. Disconnect the electrical connector. 2. Drill out the rivet. 3. Disconnect the actuator rod. 4. Remove the actuator. Rear door 3. If equipped, remove the power door lock actuator. For additional information, refer to Actuator—Door, Rear in this section. All doors 4. Remove the door latch remote control. 1. Remove the screws. 2. Disconnect the door latch remote control link from the door latch remote control. 3. Remove the door latch remote control. 5. Disconnect the door latch actuating rod from the door latch. 6. Remove the rear glass run channel. 1. Remove the bolt. 2. Remove the rear glass run channel. 7. Remove the screws and the door latch. 8. Disconnect the door latch push button rod from the door latch. 9. NOTE: Connect the remote control rod, door latch push button rod and lock cylinder rod to the front door latch (21812) before installing the new latch. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy. To install, reverse the removal procedure. ? Use the special tool to install the new rivet.

download
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-00. 2. Remove the cooling fan and the cooling fan shroud. For additional information, refer to Section 303-03. 3. Remove the accessory drive belt. For additional information, refer to Section 303-01A. 4. Remove the parts in the order indicated in the following illustration and table. 5. To install, reverse the removal procedure. 6. To install, reverse the removal procedure. Item 1: Crankshaft Pulley Bolt Removal Note 1. Remove the bolts and position the power steering cooler aside. 2. CAUTION: This bolt is torque-to-yield and cannot be reused. Using the special tool to hold the crankshaft pulley, remove and discard the damper bolt. Item 2: Crankshaft Pulley Removal Note 1. Using the special tools and two 8 mm (0.31 in) x 1.25 x 100 mm bolts, remove the crankshaft pulley. Item 3: Front Crankshaft Seal Removal Note 1. Using the special tool, remove the crankshaft front seal. Item 3: Front Crankshaft Seal Installation Note 1. Using the special tool, install the crankshaft front seal. Item 2: Crankshaft Pulley Installation Note

download
Removal 1. Remove the (A) liftgate handle to liftgate screws and the (B) liftgate handle. 2. Remove the liftgate trim panel screw access plug. 3. Remove the screw. 4. Remove the liftgate door trim panel. 1. Use Windshield and Molding/Trim Removal Kit to remove the liftgate door trim panel from the liftgate window opening. 2. Push the liftgate door trim panel toward the top of the liftgate and remove the liftgate trim panel. Installation 1. To install, reverse the removal procedure.