Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
2007 – 2008 model year North American Production Camry and Camry HV vehicles may complain of a creaking noise from the front passenger side of the vehicle. This condition may occur when the body ?exes while driving on rough roads, over speed bumps, under harsh turns or heavy braking conditions. Use the following repair procedure to address this concern. Repair Procedure 1. Remove cool air intake duct seal (for 2GR-FE). A. Remove the 7 clips and cool air intake duct seal. 2. Remove the front bumper assembly. A. Put protective tape around the front bumper assembly. NOTE Use the same procedures for the RH side and LH side. B. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip. NOTE Use the same procedures for the RH side and LH side. C. Remove the 8 screws, 2 clips, 2 radiator grille protectors, and bolt. D. Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration. Use the same procedures for the RH side and LH side. E. Without fog lights: Remove the front bumper assembly. NOTE For vehicles with fog lights: Disconnect each connector, and then remove the front bumper assembly. 3. Remove RH headlight assembly. A. Remove the bolt and 2 screws. B. Disconnect the connectors and remove the headlight assembly. 4. Remove RH rocker panel molding. A. Remove the 2 screws and rocker panel molding protector. B. Put protective tape around the rocker panel molding. Figure 8. 1 Protective Tape C. Remove the 2 screws and grommet. D. Remove the screw. E. Remove the 7 clips. F. Remove the 2 screws. G. Disengage the 8 clips and remove the rocker panel molding. 5. Remove cowl top ventilator louver sub-assembly. A. Remove the nut, front wiper arm, and blade assembly LH. B. Remove the nut, front wiper arm, and blade assembly RH. C. Disengage the claw and remove the front fender to cowl side seal LH.

download
Cherokee, Wagoneer and Comanche Models See Figures 1, 2, 3, 4, 5, 6 and 7 Fig. Fig. 1: Remove the top corner headlight bezel mounting screw Fig. Fig. 2: To access the turn signal bulb or headlight bezel mounting screws, remove the 2 turn signal housing retaining screws Fig. Fig. 3: After removing the turn signal housing from the headlight bezel, remove the 2 bezel mounting screws … Fig. Fig. 4: … then carefully pull the headlight bezel away from the headlight assembly Fig. Fig. 5: Remove the 4 headlight assembly retaining ring screws … Fig. Fig. 6: … then pull the retaining ring off of the headlight assembly Fig. Fig. 7: Pull the headlight assembly away from the vehicle just far enough to disengage the electrical connector from behind the headlight 1. Remove the headlamp bezel and retaining ring attaching screws. Remove the bezel and retaining ring. 2. Pull the headlight out, disconnect the wire harness and remove the headlight from the vehicle. 3. Install the headlight in the reverse order of removal. Grand Cherokee and Grand Wagoneer Models 1. Open the hood, reach into the engine compartment and locate the lock ring supporting the bulb assembly. 2. Rotate the lock ring 1 / 8 turn counterclockwise and pull the bulb straight out from the housing. To install: 3. Install a new bulb and position the bulb assembly in the lamp housing. 4. Rotate the lock ring 1 / 8 turn clockwise to secure.

download
WARNING: A transient high tension (25,000 V) occurs at the bulb sockets of the high intensity discharge (HID) lamps when the combination light switch is turned ON. It may cause serious electrical shock or electrocution if you do not observe the cautions below. CAUTION: – Never turn on the combination light switch before fitting the HID bulbs to their bulb sockets and completing the reassembly of the headlight assembly. – Do not service the headlights assembly in wet conditions, such as rain or snow, near a sprinkler system, or when your hands are wet to prevent electrocution. – Do not touch the surface of the HID bulbs with your bare hands and do not stain it with any oils and fats. – Do not disassemble the inverter unit and the ignitor unit. – Do not turn on the HID bulb by using a power source other than the battery mounted on your vehicle. 1. 2. 3. 4. Make sure you have the anti-theft code for the radio and the navigation system, then write down the frequencies for the radio’s preset buttons. Combination light switch OFF. Disconnect the battery negative cable, then disconnect the positive cable. Disconnect the headlight assembly 2P connector.

download
LH Headlamp Assy Part 1 OVERHAUL HINT: 1. REMOVE ENGINE UNDER COVER NO.1 2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH 3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH 4. REMOVE FRONT BUMPER COVER 5. REMOVE LH HEADLAMP ASSEMBLY a. Remove the 3 screws. Zoom Sized for Print b. Pull out the LH headlamp assembly forward, then release the
headlamp bracket.
c. Disconnect the connectors and remove the LH headlamp assembly.