Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
1. Disconnect the hood lamp harness. 1. Remove the hood insulator retainers and position the insulator away from the hood. 2. Disconnect the hood lamp harness retainers. 3. Disconnect the hood lamp electrical connector. 2. NOTE: Mark the hinge-to-hood placement to ease alignment when reinstalling the hood. Remove the hood. 1. Disconnect the windshield washer hose. 2. Remove the ground strap bolt. 3. Disconnect the hood struts. 4. Remove the four hinge-to-hood bolts and remove the hood. 3. Recover the air conditioning (A/C) system. For additional information, refer to Section 412-00. 4. Remove the lower intake manifold (9424). For additional information, refer to Intake Manifold—Lower in this section. 5. Remove the front air deflector. 1. Remove the jack handle. 2. Remove the screws. 3. Remove the air deflector.

download
CAUTION When performing service around Supplemental Inflatable Restraint (SIR) system components or wiring, the SIR system must be disabled. Failure to do so could result in possible air bag deployment, personal injury, or unneeded SIR system repairs. Catera 1. Disconnect the negative battery cable. 2. Remove the steering wheel. 3. Remove the inflatable restraint steering wheel module coil. 4. Insert a small pointed awl or wire into the ignition lock cylinder release pinhole. 5. Pull out the ignition lock cylinder. Fig. Insert a pointed tool into the release pin hole To install: 6. Install the lock cylinder. 1. Look into the hole that receives the lock cylinder on the lower RH side in order to locate the locking lever. 2. Carefully push down on the locking lever using a small flat-bladed tool until an audible click is heard. 3. Place the lock cylinder into the empty hole. 7. Install the inflatable restraint steering wheel module coil. Install the steering wheel. Deville, Fleetwood, Eldorado and Seville 1. Disable the SIR system as follows: 1. Disconnect the negative battery cable. 2. Turn the ignition switch OFF . 3. Remove the SIR fuse. On 1990 Deville and Fleetwood, remove SIR fuse No. 3 from the fuse panel. On 1991-93 Deville and Fleetwood, remove SIR fuse No. 18 from the fuse panel. On 1990-91 Eldorado and Seville, remove SIR fuse No. 19 from the fuse panel. On 1992-93 Eldorado and Seville, remove SIR fuse No. All from the engine compartment fuse panel. 4. On Deville and Fleetwood, remove the left lower sound insulator. On Eldorado and Seville, remove the left side sound insulator. 5. Remove the Connector Position Assurance (CPA) and detach the yellow 2-way connector at the base of the steering column.

download
REMOVAL PROCEDURE 1. 2. 3. 4. 5. 6. 7. Remove the right sound insulator. Remove the instrument panel compartment. Unsnap the rod from the plastic retainer on the actuator arm. Remove the two screws from the actuator (2). Disconnect the electrical connector (1). Remove the actuator (2). Inspect the air mix door for free travel. INSTALLATION PROCEDURE IMPORTANT : After replacing the actuator (2), recalibrate the actuator (2) for proper travel. Cycle the ignition ON for 3 minutes to allow the programmer and the actuator (2) to recalibrate for proper travel. 1. Install the actuator (2). 2. Connect the electrical connector (1). NOTE : Refer to Fastener Notice in Service Precautions. 3. Install the two screws to the actuator (2). Tighten Tighten the screws to 1.2 N.m (12 lb in) . 4. Snap the rod to the plastic retainer on the actuator arm. 5. Install the instrument panel compartment. 6. Install the right sound insulator.

download
1. If equipped, remove the sound insulator panel. 2. Disconnect the electrical connector at the blower motor. 3. Disconnect the electrical connector (4) from the blower motor control processor (2). 4. Remove the blower motor control processor retaining screws (3) from the HVAC module (1). 5. Remove the blower motor control processor (2) from the HVAC module (1). INSTALLATION PROCEDURE 1. Install the blower motor control processor (2) to the HVAC module (1). 2. Install the blower motor control processor retaining screws. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the screws to 1.6 N.m (14 lb in). 3. Connect the electrical connector (4) to the blower motor control processor (2). 4. Connect the electrical connector at the blower motor. 5. If equipped, install the sound insulator panel.

download
REMOVAL PROCEDURE 1. Remove the trim panel upper extension. 2. 3. 4. 5. Remove the insulator, if equipped. Remove the front door trim panel. Remove the water deflector. Disconnect the mirror wiring harness from the door. 6. Remove the nuts securing the outside mirror to the door. 7. Remove the mirror from the door. INSTALLATION PROCEDURE 1. Install the outside mirror to the door. Press the mirror into place. 2. Install the nuts in order to secure the outside mirror to the door. NOTE: Refer to Fastener Notice in Service Precautions. Tighten Tighten the outside mirror nuts to 9 N.m (80 lb in). 3. Connect the mirror wiring harness to the door. 4. Install the water deflector.