Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
1. Disconnect and isolate the battery negative cable. 2. Unsnap and fold back the screw cap below the trim panel pull handle to access and remove the screw (5) that secures the panel (2) to the pull handle bracket. 3. Unsnap and fold back the screw cap within the interior remote handle recess of the trim panel to access and remove the screw (4) that secures the panel to the inside of the door (1). The screw cap on the sedan opens from the top, and the wagon opens from the bottom. 4. Remove the four screws (6) that secure the bottom and front lower corner of the trim panel to the inside of the door. 5. Remove the two push pins (1) at the rear of the trim panel and one push pin (1) at the front edge of the trim panel. 6. Pull the trim panel (2) away from the inside of the door far enough to disengage the locator pins near the top of the panel from the door, then lift the rear of the panel upward far enough to disengage the interior door latch lock link and knob (1) from the clearance hole at the upper rear corner of the panel. 7. Reach between the top of the trim panel (3) and the inside of the door shell to unsnap the plastic clip that secures the end of the interior door handle latch release link (1) to the handle lever (2) and disengage the link from the handle. 8. Pull the trim panel (1) away from the inside of the door shell far enough to access and disconnect the door wire harness (4) connectors from the power window/lock/mirror switches (2), the door module (6), and the door courtesy lamp (5) as the vehicle is equipped. 9. Disengage the retainers (3) that secure the door wire harness to the inside of the trim panel. 10. Remove the trim panel from the inside of the door.

download
Speed nut (4x) Bolt (4x) Screws (2x) Decorative panel Armrest, lower part Bolt Expanding nut (4x) Door trim – Removing: – Remove lower part of armrest – 5 -. – Remove bolts – 3 – (2x) from door trim – 8 -. – Remove bolts – 6 – from door trim – 8 -. – Unclip decorative panel – 4 -. – Remove decorative panel – 4 – toward front. – Remove bolts – 2 – (4x) from door trim – 8 -. – Unclip door trim – 8 -. – Raise door trim – 8 – upward approx. 20 cm out from door shell. Disengage Bowden cable for interior door mechanism Disconnect electrical harness connectors – Installation: Installation is performed in the reverse order of removal. Note the following: – When installing, speed nuts – 1 – (4x) for expanding nuts – 7 – (4x) must be clipped in. – When installing, door trim must be pressed in the middle to door shell. Disengaging Bowden cable – Disconnect circlip – 3 -. – Pull Bowden cable – 1 – out of guide – 2 – and disengage. NOTE: When installing make sure that catch – 3 – faces upward. Harness connector at window regulator control module – Press catch – 2 – and disconnect harness connector – 3 – from control module in direction of arrow. – Disconnect harness connector to bass speaker

download
Removal, installation 1. Press off handle recess (3) using assembly wedge. 2. Unscrew screw (4) in the area of the interior door control 3. Unclip cover (11) and unscrew screw (12) On vehicles with front side airbag (with code 292) 4. Unscrew screw (1) on lock escutcheon (2) and remove lock escutcheon downwards 5. Press off cover (5) under armrest on door pocket and unscrew screw (6) 6. Unclip entrance lamp and disconnect electrical connection 7. Press door lining (8) off inner door panel at bottom, front and rear using assembly wedge Note: Guide each assembly wedge straight to the clips 8. Lift door lining (8) upwards off retaining clips at the top of the sealing rail using assembly wedge and at the same time pull away from the inner door panel 9. Unhook control cable on interior door control 10. Pull electrical connections off door lining (8). 11. Put down door lining (8) 12. Check films and clips on inner door panel and replace if necessary. Note: Stick door film to inner door panel 13. Check clips (9) on door lining (1) and replace if necessary 14. Install in reverse order References, Special tools

download
All Vehicles 1. Remove the rear door interior trim panel. For additional information, refer to INTERIOR TRIM AND ORNAMENTATION . 2. Remove the access hole watershield. 3. Reconnect the window regulator and window switch electrical connectors and position the front door window to access the glass clamp bolt.4. Disconnect the window regulator and window switch electrical connectors 5. Loosen the window glass clamp bolt. 6. Tape the window in the full up position, then lower the window regulator downward until it reaches the stops at the bottom of the regulator track. 7. Remove the interior door handle bolt. 8. Disconnect the rear door latch assembly electrical connector.

download
1.Screw 2. Lock cover plate 3. Handle recess 4. Screw 5. Cover 6. Screw 8. Door 9. Clips 10. Installation wedge 11. SRS cover (with code 293 rear side airbag) 12. Screw (with code 293 rear side airbag) 13. Clip
14. Control cable (interior door control) Special tools 7. Press door lining (8) off inner door panel at bottom, front and rear using assembly wedge Guide each assembly wedge straight to the clips 8. Lift door lining (8) out of retaining clips at the top of the sealing rail using assembly wedge and at the same time pull away from the inner door panel 9. Unhook control cable (14) on interior door control Installation: Ensure that the control cable (14) is clipped into the retaining clip (13) 10. Pull electrical connections off door lining (8) 11. Put down door lining (8) 12. Check film and clips on inner door panel and replace if necessary. Stick door film onto inner door panel. 13. Check clips (9) on door lining and replace if necessary 14. Install in reverse order