Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
- with CODE (U49) Styling Package Remove/Install 1 Remove cover (1) from bumper NOTE: Do not break retaining lugs. 2 Remove bulb housing (2) NOTE: To unlock, rotate counterclockwise. Installation: Ensure that the locking device has locked securely. 3 Remove fog lamp insert (6) from housing Installation wedge: See Special Tools below. 4 Disconnect connector (4) 5 Remove bulb on the back of the fog lamp insert (6) CAUTION: Do not hold the bulb with bare fingers, as fingerprints bake and leave behind opaqueness on the bulb. Use a soft, lint-free cloth. NOTE: Lock securely. 6 Install in the reverse order Special Tools

download
1. Open the rear liftgate.2. Remove the two screws that attach both the left and right tail lamp assemblies and remove the lamps from the body. 3. Inspect the part number on both the left and right tail lamp circuit boards. Chevrolet – New P/N 16532713 Chevrolet Export – New P/N 16532714 Buick and Oldsmobile – New P/N 16532715 GMC – New P/N 16532716 • If the part number printed on a circuit boards IS one of the part number listed above, then the circuit board is the new design and does NOT need to be replaced. • If the part number printed on a circuit board is NOT one of the part numbers listed above, then the circuit boards is the old design and MUST BE REPLACED. Proceed to the next step if either circuit board needs to be replaced. 4. Turn on the tail lamps, directional signals, etc. and determine if there are any bulbs that require replacement. 5. Disconnect the electrical connector from the circuit board being replaced. 6. Remove the three screws attaching the circuit board to the tail lamp and remove the circuit board. 7. Install a NEW stop lamp bulb in a NEW circuit board. • On Chevrolet, Buick and Oldsmobile vehicles, the stop lamp bulb is located in the UPPER (top) socket in the circuit boards. • On GMC vehicles, the stop lamp bulb is located in the LOWER (bottom) socket in the circuit board. Important: This special policy will cover the cost of replacing the stop lamp bulb(s). All other bulbs that require replacement are to be submitted under the normal warranty operation, if applicable. 8. Transfer the remaining bulbs from the old circuit board to the new circuit board. Replace any burned out bulbs. 9. Connect the electrical connector to the new circuit board(s). 10. Turn on the tail lamps, directional signals, etc. and verify that all bulbs are functional. 11. Install the circuit board to the tail lamp and install the three screws.

download
Some 2002-2004 model year Chevrolet TrailBlazer and TrailBlazer EXT, GMC Envoy and Envoy XL, Oldsmobile Bravada vehicles, and 2004 Buick Rainier vehicles have tail lamp/stop lamp(s) that may become inoperative. Service Procedure 1. Open the rear liftgate. 2. Remove the two screws that attach both the left and right tail lamp assemblies and remove the lamps from the body. 3. Inspect the part number on both the left and right tail lamp circuit boards. Chevrolet – New P/N 16532713 Chevrolet Export – New P/N 16532714 Buick and Oldsmobile – New P/N 16532715 GMC – New P/N 16532716 • If the part number printed on a circuit boards IS one of the part number listed above, then the circuit board is the new design and does NOT need to be replaced. • If the part number printed on a circuit board is NOT one of the part numbers listed above, then the circuit boards is the old design and MUST BE REPLACED. Proceed to the next step if either circuit board needs to be replaced. 4. Turn on the tail lamps, directional signals, etc. and determine if there are any bulbs that require replacement. 5. Disconnect the electrical connector from the circuit board being replaced. 6. Remove the three screws attaching the circuit board to the tail lamp and remove the circuit board. 7. Install a NEW stop lamp bulb in a NEW circuit board. • On Chevrolet, Buick and Oldsmobile vehicles, the stop lamp bulb is located in the UPPER (top) socket in the circuit boards. • On GMC vehicles, the stop lamp bulb is located in the LOWER (bottom) socket in the circuit board. 8. Transfer the remaining bulbs from the old circuit board to the new circuit board. Replace any burned out bulbs. 9. Connect the electrical connector to the new circuit board(s). 10. Turn on the tail lamps, directional signals, etc. and verify that all bulbs are functional. 11. Install the circuit board to the tail lamp and install the three screws.

download
1. Remove the sail panel. NOTE: Release the top portion first. 2. Remove the window regulator switch plate. 3. Disconnect the electrical connectors. 4. Remove the top door trim panel screw. 2001 Ford Truck Expedition 2WD V8-4.6L SOHC VIN W 5. Remove the door trim panel screw at the window regulator switch plate opening. 6. Remove the door trim panel screw in the courtesy lamp housing. 1 Remove the courtesy lamp lens. 2 Remove the screw. 7. Release the inside door handle trim cover. ^ Pull the inside door handle outward. ^ Release the trim cover. 8. Remove the inside door handle. ^ Remove the bolt.9. Lift upward and then outward to remove the front door trim panel. CAUTION: To avoid damage to the front door trim panel, do not pull directly outward. 10. Remove the courtesy lamp. ^ Turn the courtesy lamp bulb socket one-quarter of a turn and remove. 11. Disconnect the power mirror electrical connector. INSTALLATION

download
NOTE: High series shown, low series similar. NOTE: The window must be completely down to remove the front door trim panel. 1. On high series front door trim panel, disconnect the battery ground cable. 2. Remove the screws. 3. Remove the inside door handle cup. 4. On low series front door trim panel, remove the screw and the window regulator handle. 1997 Ford Truck Explorer 2WD V6-245 4.0L VIN X SFI 5. Start in a lower corner and work around the panel, carefully prying the front door trim panel away from the front door to disengage the pushpins. 6. Lift the front door trim panel to disengage the top lip from the weatherstrip. 7. Turn the front door trim panel over. 1997 Ford Truck Explorer 2WD V6-245 4.0L VIN X SFI 8. Disconnect the power window switch and the power door lock switch electrical connectors. a. Remove the screws. b. Disconnect the electrical connectors. 9. If equipped, remove the courtesy lamp bulb from the lens and remove the front door trim panel. Installation 1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy. To install, reverse the removal procedure.