Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Throttle Body And TPS – Remove throttle body, refer to COMPONENT REPLACEMENT AND REPAIR PROCEDURES. Throttle Stop Screw – Check that there is no clearance between throttle stop screw and lever with throttle plate in the fully closed position. TPS Screws – Loosen throttle position sensor set screws. TPS Adjustment Connect ohmmeter across throttle sensor terminals E2 and IDL. – Insert a 0.0157 in (0.40 mm) feeler gauge between throttle stop screw and lever. TPS Adjustment – Slowly turn sensor clockwise until ohmmeter shows no continuity. – Tighten sensor set screws. – Check adjustment with the following feeler gauges and note ohm reading: 0.010 in (0.25 mm) – Continuity 0.0335 in (0.85 mm) – No continuity – If desired results cannot be achieved, readjust sensor. If readings still cannot be achieved, replace sensor.

download
HINT: – The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. – When the power back door drive unit, back door w/motor lock and battery is reconnected, the back door is locked and therefore cannot be opened. Therefore, it is necessary to unlock the back door using the door control switch or transmitter switch. 1. REMOVE BACK DOOR TRIM BOARD LH a. Using a screwdriver, disengage the 3 claws and remove the trim board. HINT: Tape the screwdriver tip before use. 2. REMOVE BACK WINDOW PANEL TRIM UPPER a. Using a screwdriver, disengage the 2 claws and 7 clips, and remove the trim upper. HINT: Tape the screwdriver tip before use. 3. REMOVE ROOF HEADLINING ASSY 4. REMOVE POWER BACK DOOR DRIVE UNIT a. Remove 2 bolts A indicated in the illustration. b. Remove the 4 bolts and drive unit. c. Disconnect the connector.5. REMOVE BACK DOOR TRIM PANEL ASSY UPPER a. Using a screwdriver, disengage the 10 clips and remove the trim panel. HINT: Tape the screwdriver tip before use. 6. REMOVE BACK DOOR TRIM PANEL ASSY a. Using a screwdriver, disengage the 8 clips and remove the trim panel. HINT: Tape the screwdriver tip before use. 7. REMOVE BACK DOOR TRIM COVER RH a. Using a screwdriver, disengage the 3 clips and remove the trim cover. HINT: Tape the screwdriver tip before use. 8. REMOVE BACK DOOR TRIM COVER LH HINT: Use the same procedures described for the RH side. 9. REMOVE BACK DOOR TRIM SPACER RH a. Remove the screw. b. Using a clip remover, disengage the claw and remove the trim spacer. 10. REMOVE BACK DOOR TRIM SPACER LH

download
Some customers may experience a squeak noise due to contact between the seat track locating pin(s) and the floor pan location hole(s). The following procedure describes the repair method to correct this condition. S 2004 – 2007 model year Lexus vehicles. 1. Disconnect the negative (–) battery terminal. 2. Remove the plastic front seat track covers — Use a screwdriver to disengage the claws and carefully remove the plastic seat track covers. NOTE: Tape the screwdriver tip before use. NOTE: Refer to the appropriate Lexus Repair Manual for each model for detailed instructions on how to remove the plastic seat track covers.

download
1. Disconnect battery ground cable, then fully lower steering wheel. 2. Remove finish panel screws and connectors, Figs. 17 through 20 . Fig. 21 Instrument Cluster Screw Locations 3. Remove cluster screws and disconnect electrical connectors. 4. Remove cluster assembly. 5. Reverse procedure to install.

download
Fig. 26 Wiper Component Locations 1. Disconnect battery ground cable and disable airbag system as described under MAINTENANCE PROCEDURE/AIRBAG SYSTEM DISARMING. 2. Remove wiper arm and blade assemblies, Fig. 26. 3. Remove hood to cowl seal and cowl louver. 4. Remove five set bolts, then disconnect electrical connector. 5. Raise front side of wiper motor and link assembly up and remove wiper motor and link assembly. 6. Remove wiper motor cover. 7. Reverse procedure to install, torque four bolts to 48 in. lb.