Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Passive anti-theft system is designed to prevent vehicle theft. The Security Alarm Module (SAM) is a logic controlled device that monitors vehicle doors, hood, liftgate and ignition action for unauthorized operation. The alarm activates by sounding the horn, flashing the headlamps, park and tail lamps and providing an engine kill feature. Passive arming occurs upon normal vehicle exit (open door, lock with power locks, close door). The Security lamp in the panel will flash for 15 seconds, indicating that arming is in progress. Note that this 15 second arming period will start after the Illuminated Entry has timed out (courtesy lamps off). If no monitored systems are activated during this period, the system will arm. If the hood switch is not seen by the system, the Security lamp will remain steadily lit during the arming process, although the system will still arm. Active arming occurs when the Remote Keyless Entry transmitter is used to lock the vehicle doors, whether the doors are open or closed. If one or more doors are open, the arming sequence is completed only after all doors and liftgate are closed. Passive disarming occurs upon normal vehicle entry (unlocking either door with the key). This disarming will also halt the alarm once it has been activated. Active disarming occurs when the Remote Keyless Entry transmitter is used to unlock the vehicle doors. This disarming will also halt the alarm once it has been activated.

download
Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section. Remove the liftgate scuff plate by pulling upward. 6. Remove the pin-type retainers and pull back the carpeting. Remove the rear floor loadspace trim panel. 7. Remove the two bolts and the loadspace trim panel by pulling upward. Remove the floor jack assembly.8. Remove the third row seat safety belt anchor bolt. 11. Remove the rear door scuff plate by pulling upward. 9. Remove the rear quarter trim panel pin-type retainer. 12. Fold the third row seat down. 13. Remove the rear quarter trim panel by pulling outward. • If equipped, disconnect the power point and power third row seat switch electrical connector at the rear. 10. Remove the second row safety belt anchor. 14. To install, reverse the removal procedure.

download
Vehicle Identification Special badging is used to identify the GMC Yukon, Chevrolet Tahoe & Cadillac Escalade Two-mode Hybrid vehicles. One of these emblems is located on the lower right corner of the vehicle’s liftgate. The eighth digit of the Vehicle Identification Number (VIN) can also be used to identify a Two- mode Hybrid vehicle. If the eighth digit is a five (5), this signifies the vehicle is a Hybrid. A Hybrid badge is also located on the right and left C-pillars When the hood is opened, indications that a Two-mode Hybrid system is present include a Hybrid badge and a HIGH VOLTAGE WARNING label on the power electronics cover. Under the second row, rear seat sub-floor is a DANGER HIGH VOLTAGE label attached to the Hybrid battery case, indicating high voltage. A tachometer with Auto Stop indicator and an Economy gauge are unique to these vehicles Note: All high voltage cables used in Two- mode Hybrid models are colored orange for

download
BUMPER COVER – REAR Exploded View Removal and Installation 1. Remove the 2 rear bumper cover lower screws (1 each side). To install, tighten to 5 Nm (44 lb-in) . 2. Remove the 4 rear bumper cover center screws. 3. Remove the 2 rear bumper cover lower pushpins. 4. Remove the 2 rear splash shield-to-rear bumper cover screws (1 each side). 5. Remove the 2 rear bumper cover upper screws (1 each side). To install, tighten to 5 Nm (44 lb-in) . 6. Remove the 2 liftgate alignment bumper bolts and the 2 liftgate alignment bumpers. To install, tighten to 8 Nm (71 lb-in) . 7. Disconnect the parking aid system or trailer tow electrical connector, if equipped. 8. Remove the rear bumper cover. 9. To install, reverse the removal procedure. When installing, position the rear bumper cover into the bumper slides.