Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
WARNING: A transient high tension (25,000 V) occurs at the bulb sockets of the high intensity discharge (HID) lamps when the combination light switch is turned ON. It may cause serious electrical shock or electrocution if you do not observe the cautions below. CAUTION: – Never turn on the combination light switch before fitting the HID bulbs to their bulb sockets and completing the reassembly of the headlight assembly. – Do not service the headlights assembly in wet conditions, such as rain or snow, near a sprinkler system, or when your hands are wet to prevent electrocution. – Do not touch the surface of the HID bulbs with your bare hands and do not stain it with any oils and fats. – Do not disassemble the inverter unit and the ignitor unit. – Do not turn on the HID bulb by using a power source other than the battery mounted on your vehicle. 1. 2. 3. 4. Make sure you have the anti-theft code for the radio and the navigation system, then write down the frequencies for the radio’s preset buttons. Combination light switch OFF. Disconnect the battery negative cable, then disconnect the positive cable. Disconnect the headlight assembly 2P connector.

download
CHECK THAT PEDAL HEIGHT IS CORRECT Pedal height from floor panel: 42.8-152.8 mm (5.62-6.02 in.) If the pedal height is incorrect, adjust it. IF NECESSARY, ADJUST PEDAL HEIGHT (a) Remove the under cover. (b) Remove the lower pad and air duct. (c) Remove the power steering ECU and disconnect the connector from the stop light switch. (d) Loosen the stop light switch lock nut and remove the stop light switch. (e) Loosen the push rod lock nut. (f) Adjust the pedal height by turning the pedal push rod. (g) Tighten the push rod lock nut. Torque: 25 N?m (260 kgf?cm, 19 ft?lbf) (h) Install the stop light switch and turn it until it lightly contacts the pedal stopper. (i) Return the stop light switch one turn. (j) Check that the clearance (A) between stop light switch and pedal. Clearance: 1.5-2.6 mm (0.06-0.10 in.) (k) Tighten the stop light switch lock nut.

download
1988 Wiring Diagrams General Motors IDENTIFICATION COMPONENT LOCATIONS Component A/C System Alternator Audio Alarm Module Back-Up Light Switch Cigarette Lighter Clutch Start Switch Coolant Fan Relay Cruise Control (2.5L Vin R) Cruise Control (2.8L Vin 9) Defogger Timer Relay Distributor (DIS) Distributor (EST) Door Ajar Switches Dome Lights ECM (2.5L Vin R) ECM (2.8L Vin 9) EHPS Controller Fuel Pump Relay Fuel Tank Unit Fuse Block Gear Select Switch Headlight Door Module Horn Relay Horns Hood Ajar Switch Ignition Switch Instrument Cluster Light Switch Lumbar/Bolster Control Switches Panel Instrument Light Control Power Door Locks Power Mirror System

download
Instrument panel, airbag assembly passenger disable switch, multifunction control module, transmission selector lamp, engine coolant blower motor control module F5 Air conditioning (AC), stop lamps, anti-lock brake system (ABS), engine coolant blower motor relay F6 Clock, multifunction control module, instrument panel, boot lid/tailgate lamp F7 Heated rear window Engine management, air conditioning (AC), engine coolant blower motor relay, engine coolant blower motor control module F10 Hazard warning lamps, interior lamps Light switch, hazard warning lamps, clock, instrument illumination, headlamp adjustment, audio system, air conditioning (AC), automatic transmission (AT), heated rear window, heated seat – driver’s side F12 Rear fog lamps F13 Convertible top system relay F14 Rear electric windows, heated seats F15 Trailer socket

download
Disconnect battery negative lead. Remove fixture for steering column switch. Remove center console. Remove trim for center console. Remove right glovebox. Remove all clip-fitted trims (on instrument panel). Remove carrier in center console. Remove both panels for front roof pillar. Remove light switch unit. Remove complete instrument carrier. Remove heating controls. If necessary, remove radio receiver. Remove airbag module on passenger side. If necessary, release screw (1).