Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Removal 1. Raise and support vehicle. Remove front wheel. Remove shock absorber. See LOWER CONTROL ARM & BALL JOINT . Remove hub grease cap. Remove ABS speed sensor and wire harness clamp from steering knuckle. Remove brakeline bracket from steering knuckle. Remove the bolt and separate the brake tube bracket from the steering knuckle. Using Special Tool (09023-00100), disconnect the brake tube from the front disc brake caliper assembly. Remove the bolt and separate the brake tube bracket from the steering knuckle. Remove the 2 bolts and front disc brake caliper assembly. Remove rotor. 2. On 4WD models, using a screwdriver and a hammer, remove the front axle hub grease cap. Remove the cotter pin and a lock cap. Remove the front axle hub nut. On all models, remove the nut and separate the stabilizer link assembly from the steering knuckle. Remove the cotter pin. Using Special Tool (09628- 62011), separate the tie rod end sub-assembly from the steering knuckle. 3. Remove 2 lower ball joint bolts, and disconnect lower ball joint. Remove upper ball joint, cotter pin and retaining nut. Using ball joint separator, separate upper ball joint from knuckle. On 4WD models, using a plastic hammer, separate the front axle hub from the front drive shaft. Remove the front axle hub sub- assembly. On all models, remove steering knuckle with hub. Installation To install, reverse removal procedure. Clean bolt threads. Tighten bolts and nuts to specification. See TORQUE SPECIFICATIONS . Depress brake pedal several times. Check front wheel alignment. Ensure ABS speed sensor has a good signal.

download
1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD 2. REMOVE COOL AIR INTAKE DUCT SEAL 3. REMOVE ENGINE ROOM SIDE COVER LH 4. REMOVE ENGINE ROOM SIDE COVER RH 5. DISCHARGE REFRIGERANT FROM REFRIGERATION (a) Start up the engine. (b) Turn the A/C switch on. (c) Operate the cooler compressor at an engine rpm of approximately 1,000 for 5 to 6 minutes to circulate the refrigerant and collect compressor oil remaining in each component into the cooler compressor as much as possible. (d) Stop the engine. (e) Using SST, let the refrigerant gas out. 6. DISCONNECT CABLE FROM NEGATIVE BATTERY CAUTION: Wait for 90 seconds after disconnecting the cable to prevent airbag deployment 7. REMOVE FRONT UPPER FENDER PROTECTOR LH 8. REMOVE FRONT UPPER FENDER PROTECTOR RH 9. REMOVE ROOF DRIP SIDE FINISH MOULDING LH 10. REMOVE ROOF DRIP SIDE FINISH MOULDING RH 11. REMOVE FRONT WIPER ARM HEAD CAP 12. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH 13. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH 14. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY 15. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY 16. SEPARATE SUCTION PIPE SUB-ASSEMBLY (a) Remove the bolt, and slide the hook connector. (b) Disconnect the suction pipe sub-assembly. (c) Remove the O-ring from the suction pipe sub-assembly. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering. 17. SEPARATE LIQUID TUBE SUB-ASSEMBLY (a) Disconnect the liquid tube sub-assembly. (b) Remove the O-ring from the liquid tube sub-assembly. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering. 18. REMOVE HEATER WATER OUTLET HOSE

download
Fig. 26 Wiper Component Locations 1. Disconnect battery ground cable and disable airbag system as described under MAINTENANCE PROCEDURE/AIRBAG SYSTEM DISARMING. 2. Remove wiper arm and blade assemblies, Fig. 26. 3. Remove hood to cowl seal and cowl louver. 4. Remove five set bolts, then disconnect electrical connector. 5. Raise front side of wiper motor and link assembly up and remove wiper motor and link assembly. 6. Remove wiper motor cover. 7. Reverse procedure to install, torque four bolts to 48 in. lb.

download
1. REMOVE BACK DOOR ASSIST GRIP a. Using a screwdriver, open the covers. HINT: Tape the screwdriver tip before use. b. Remove the 2 screws and assist grip. 2. REMOVE BACK DOOR PULL STRAP a. Using a screwdriver, remove the strap cover. HINT: Tape the screwdriver tip 3. REMOVE CENTER GARNISH Using a screwdriver, remove the center garnish. HINT: Tape the screwdriver tip before use. 4. REMOVE SIDE GARNISH a. Using a screwdriver, remove the side garnish. HINT: Tape the screwdriver tip before use. b. Employ the same manner described above to the other side. 5. REMOVE DOOR TRIM BOARD a. Insert a screwdriver between the door and door trim board to pry the door trim board out. NOTE: Be careful not to damage the door and door trim board. HINT: Tape the screwdriver tip before use. b. Pull the door trim board to remove it. 6. REMOVE HIGH-MOUNTED STOP LIGHT a. Remove the 2 screws. b. Disconnect the connector. c. Remove the high-mounted stop light. 7. REMOVE WASHER NOZZLE 8. REMOVE REAR WIPER ARM Remove the nut, rear wiper arm. Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf) 9. REMOVE WIPER MOTOR AND LINK ASSEMBLY a. Remove the 3 bolts from the wiper motor. b. Remove the 2 bolts and wiper motor and link assembly. Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf) c. Remove the grommet. 10. REMOVE COMBINATION LIGHTS 11. REMOVE LICENSE PLATE LIGHT ASSEMBLY a. Disconnect the back door control cable from the handle lever. b. Disconnect the connector. c. Remove the 3 nuts. d. Using a screwdriver, remove the license plate light assembly. HINT: Tape the screwdriver tip before use. e. Remove the handle lever from the license plate light cover. f. Remove the license plate light assembly from the license plate light cover. 12. REMOVE KEY CYLINDER