Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
1. Disconnect battery ground cable (14301) . Refer to Section 14-01. 2. Remove steering wheel (3600) as described. 3. Remove steering column from vehicle as described. 4. Remove steering column lower yoke (3N725) , steering column upper bearing spring (3520) , suspension height sensor control ring (3C131) and steering column bearing tolerance ring (3L539) . Lower Steering Column Assembly 5. Remove turn indicator cancel cam (13318) by pushing up with flat-bladed screwdriver. Note direction of flush surface. 6. Remove ignition switch (11572) . 7. Remove bearing retainer (3C610) and steering column upper bearing spring . 8. Remove steel steering column bearing tolerance ring and steering column bearing sleeve (3518) . 9. Remove plastic bearing retainer from ignition switch lock cylinder bore. 10. Remove metal steering column lock housing bearing (3E700) from ignition switch lock cylinder bore. 11. Note position of steering column lock gear (3E717) to actuator lock. Remove steering column lock gear . 12. Remove two pivot bolts. Use caution as steering column position spring (3D655) will release when bolts are removed. Remove steering column lock cylinder housing (3511) . 13. Remove steering column shaft assembly from steering column. 14. Remove steering column lock lever actuator (3E715) and steering actuator housing (3F723) . 15. Remove lower steering column bearing (3517) and steering column lower bearing retainer (3D681) . 16. Remove tilt position lever pivot pin using a drift. Remove RH steering column locking lever (3B661) (RH and LH), steering column lock left hand lever (3D653) and steering column locking lever springs (3B664) . Assembly 1. Install steering column shaft assembly into steering actuator housing . 2. Install lower steering column bearing and steering column mounting bracket (3E660) . Tighten screws to 7-11 Nm (62-97 lb-in). 3. Install suspension height sensor control ring , steering column bearing tolerance ring , steering column upper bearing spring and steering column lower yoke to steering column shaft assembly. Tighten pinch bolt to 25-35 Nm (19-25 lb-ft). Item 1 2 3 4 5 A 4. Position actuator cam in steering column lock cylinder housing and install cam pivot pin with small hammer. Tap pin in until flush with steering column lock cylinder housing . 5. Install one steering column locking lever spring and RH steering column locking lever into steering actuator housing using a drift to hold in place. 6. Install the LH steering column locking lever spring and steering column lock left hand lever with steering column lock actuator lever pin (3F530) . Tap steering column lock actuator lever pin into place while driving out drift. Part Number N803942 3L539 3C131 3520 3N725 — Description Pinch Bolt Steering Column Bearing Tolerance Ring Suspension Height Sensor Control Ring Steering Column Upper Bearing Spring Steering Column Lower Yoke Tighten to 25-35 Nm (19-25 Lb-Ft)

download
Latch—Door Removal and Installation NOTE: Front door shown, rear door similar. Front door 1. Remove the door lock cylinder; refer to Lock Cylinder—Door. 2. If equipped, remove the power door lock actuator. 1. Disconnect the electrical connector. 2. Drill out the rivet. 3. Disconnect the actuator rod. 4. Remove the actuator. Rear door 3. If equipped, remove the power door lock actuator. For additional information, refer to Actuator—Door, Rear in this section. All doors 4. Remove the door latch remote control. 1. Remove the screws. 2. Disconnect the door latch remote control link from the door latch remote control. 3. Remove the door latch remote control. 5. Disconnect the door latch actuating rod from the door latch. 6. Remove the rear glass run channel. 1. Remove the bolt. 2. Remove the rear glass run channel. 7. Remove the screws and the door latch. 8. Disconnect the door latch push button rod from the door latch. 9. NOTE: Connect the remote control rod, door latch push button rod and lock cylinder rod to the front door latch (21812) before installing the new latch. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy. To install, reverse the removal procedure. ? Use the special tool to install the new rivet.

download
Multi-Function Switch Removal 1. Disconnect battery ground cable (14301). 2. Tilt column to lowest position and remove tilt steering column lock lever (3F527). 3. Remove ignition switch lock cylinder (11582). 4. Remove shroud screws and remove upper steering column shroud (3530) and lower steering column shroud. 5. Remove two self-tapping screws retaining multi-function switch (13K359) to steering column casting. Disengage multi-function switch from casting. 6. Disconnect the two electrical connectors. Installation 1. Install two electrical connectors to full engagement. 2. Align mounting holes in multi-function switch with corresponding holes in steering column casting. Install two self-tapping screws, making sure to start screws in the previously tapped holes. Tighten to 2-3 Nm (18-26 lb-in). 3. Install upper steering column shroud and lower steering column shroud. 4. Install ignition switch lock cylinder. 5. Install tilt steering column lock lever. 6. Connect battery ground cable. 7. Check steering column and multi-function switch for proper operation.

download
You will also see how to change window glass and electric window motor in this series. First, unscrew the 7 screws holding on the door panel. Next you carefully pry off the tweeter cover that is where the mirror is. Lift the panel up and off of the door. Undo all of the wiring connections except for the window controller. Open the 2 black rubber view ports (Circled in Yellow) and roll the window up or down until you see the 10mm bolts that hold the window in place. Loosen, but don’t remove these bolts. Slide the window up, and tape it up, or remove the window and set aside. Next, unplug the door lock plug and move the door panel out of the way. Unscrew the gold 10mm bolts that hold on the metal inner door panel (circled in green in pic5). Also remove the Phillips screw that holds the inner door handle on (circled in red on pic 5) Unscrew the small bolt that holds on the lock cylinder that is behind the quarter-sized black cap on the side of the door. Be careful with that little bolt or it will fall into never never land .

download
1. CAUTION: Do not remove the steering column, steering wheel (3600) and driver side air bag module (043B13) as an assembly from the vehicle unless the steering column is locked to prevent rotation, or lower end of steering shaft is wired in such a way to prevent the steering wheel from being rotated. NOTE: All steering column components are assembled with fasteners. They are designed with a thread-locking system to prevent loosening due to vibrations associated with normal vehicle operation. Make sure the front wheels are in the straight-ahead position. Disconnect battery ground cable (14301). Refer to Section 14-01. Disconnect air bag backup power supply. Refer to Section 01-20B. 2. Remove steering wheel as described. 3. Remove RH and LH lower mouldings from instrument panel (04320) by pulling up and snapping out of retainers. 4. Remove instrument panel steering column cover (04459). 5. Remove air bag sliding contact (14A664) as described. 6. Remove tilt wheel handle and shank (3F609) by unscrewing it from steering column. 7. Rotate ignition switch lock cylinder (11582) to RUN position. Using a 1/8-inch drift, depress ignition switch retaining pin through access hole and remove ignition switch lock cylinder. 8. Remove four retaining screws from lower steering column shroud (3530) . Remove lower steering column shroud and upper steering column shroud. 9. Remove two instrument panel reinforcement brace bolts. Remove reinforcement. 10. Remove steering column to parking brake control shake brace. 11. Disconnect shift cable and bracket (7E395) from steering actuator housing (3F723) by removing one screw. 12. Remove two multi-function switch retaining screws and set multi-function switch (13K359) aside.