Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Headlamp Assembly NOTE: Make sure the headlamp switch and ignition switch are in the OFF position. 1. To remove individual components, only carry out the following steps. Component Radiator grille opening cover Radiator sight shield Headlamp assembly 2. View 1 of 2. Remove the components in the order indicated in the following illustration and table. 3. View 2 of 2. Remove the components in the order indicated in the following illustration and table. 4. To install, reverse the removal procedure. Item 2: Radiator Grille Opening Cover Removal Note 1. Position the ambient air temperature sensor aside. Item 6: Standard Headlamp Disassembly Note 1. To remove individual components, only carry out the following steps. Component Low beam bulb High beam bulb Side marker module 2. Disassemble the components in the order indicated in the following illustration and table. Steps 1-2, 4-5 6-7, 9-10 11-14 3. To assemble, reverse the disassembly procedure. Items 5 and 10: Low and High Beam Bulb Removal Note WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury. 1. The headlamp bulb should not be removed from the headlamp until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp with the bulb removed from the leadlamp. Item 6: HID Headlamp Disassembly Note 1. To remove individual components, only carry out the following steps. Component HID ballast and bulb 1-2, 4-7, 9-11 High beam bulb Side marker module 2. Disassemble the components in the order indicated in the following illustration and table. Steps 12-13, 15-16 17-20

download
DETAILS/RESULTS/ACTIONS Use the recorded results from the LCM self-test. Are any DTCs retrieved? Yes If DTC B1470 is retrieved, GO to GO to C8 . If DTC B1342 is retrieved, CLEAR DTC and CARRY OUT LCM On-Demand Self-Test. INSTALL a new LCM if DTC B1342 is retrieved again. REFER to Section 419-10. TEST the system for normal operation. If other DTC(s) is (are) retrieved, RETURN to the LCM Diagnostic Trouble Code (DTC) Index. No If only the autolamps are inoperative, GO to Pinpoint Test I. Otherwise, GO to C2 . Trigger the LCM active command HEAD/CORNERING LAMP CONTROL LOW BEAM. Do the headlamps turn ON? Yes GO to C3. No GO to C5. Monitor the LCM PID HDLMPSW while turning the headlamp switch to the headlamps ON position. Does the PID display ON? Yes INSTALL a new LCM; REFER to Section 419-10. TEST the system for normal operation. No GO to C4. Check the headlamp switch; refer to the Wiring Diagrams Cell 149. Is the headlamp switch OK? Yes REPAIR circuit 1033 (RD/YE) for open. TEST the system for normal operation. No INSTALL a new headlamp switch. REFER to Lamp Switch—Headlamp in this section. TEST the system for normal operation. C5 CHECK CIRCUIT 221 (OG/WH) FOR BATTERY VOLTAGE

download
1. 2. 3. 4. 5. Raise vehicle on a hoist. Remove wheel and tire. Remove splash shield as necessary to access headlamp housing. See Fig. 10. Remove grille. Remove the two fascia bolts from behind the grille. See Fig. 19. 1 – ATTACHING POINTS 2 – FRONT FASCIA 6. Remove fasteners attaching fender to fascia on the side being worked on. 7. Remove the three fasteners holding the lower fascia (3) to the lower radiator crossmember. 8. Make sure there is a slight gap (1) between the fender and fascia. 9. Disconnect wire connectors (2, 5, and 7). 10. Remove four nuts (1, 3, and 6) attaching headlamp housing (4). 1 – MOUNTING HOLES 2 – FRONT SIDE MARKER/PARK/TURN SIGNAL LAMP 3 – MOUNTING HOLES 4 – HEADLAMP HOUSING 5 – LOW BEAM CONNECTOR 6 – MOUNTING HOLE 7 – HIGH BEAM CONNECTOR 11. Once the fascia (3) is loosened on the appropriate side and there is a gap between the fascia and the headlamp unit (1), place a shop towel underneath the headlamp unit (2) on the fascia (3) to protect it from scratches and marring. 12. Tilt the bottom of the headlamp unit (1) forward and then pull straight out of fender/fascia opening, taking care not to damage headlamp unit, fender, or fascia (2).

download
1. Disconnect the negative battery cable. 2. Remove the front bumper. (See FRONT BUMPER REMOVAL/INSTALLATION .) 3. Remove in the order indicated in the figure(s). 4. Install in the reverse order of removal. 5. Adjust the headlight aiming. (See HEADLIGHT ADJUSTMENT .) HEADLIGHT ADJUSTMENT 1. 2. 3. 4. 5. Adjust the tire air pressure to the specification. Position the unloaded vehicle on a flat, level surface. Seat one person in the driver’s seat. Position the vehicle straight ahead and perpendicular to a wall. Set the headlights 3 m {10 ft} from the wall. Fig. 6: Positioning Vehicle In Front Of Vertical Wall 6. 7. 8. 9. While adjusting one headlight, disconnect the connector of the other. Start the engine to charge the battery. Turn on the low-beam headlight. Adjust the headlights by turning the adjusting screws as shown in the figure. Loosen the screws first, then tighten them. NOTE: If the adjusting screws are tightened first, then loosened, they will continue to loosen when the vehicle is in motion and may cause the headlights to become misaligned.

download
Replacing Low Beam Headlamp NOTE: Left Low Beam Headlamp M29 and Right Low Beam Headlamp M31 can be checked via output Diagnostic Test Mode (DTM) of Vehicle Electrical System Control Module J519. Removing: Switch off ignition and all electrical components and move ignition key or start button into position 0 (preliminary engaged position). NOTE: During removal and installation, leave ignition key with remote control inside the vehicle to prevent the doors from locking and possibly activating the “Coming Home / Leaving Home” functions on its own. In order to be able to replace low beam headlamp, it is sometimes necessary to remove neighboring components at the corresponding headlamp. Refer to the following tables to determine additional component removal as required, depending on engine. NOTE: Low beam headlamp bulb -2- is clipped into the reflector -1-. When removing low beam headlamp bulb – 2-, the harness connector – 3-is not disconnected first. Push harness connector and thereby the lamp socket in -direction of arrow- until the lamp can be felt as loose. Pull low beam headlamp at harness connector -3- out of reflector. Pull low beam headlamp -2- from harness connector -1-. Installing: NOTE: When installing cap, ensure proper seating. Water intrusion will damage headlamp. Do not touch the glass of the light bulb, when installing. Your fingers will leave traces of grease on the glass which, when the light is switched on, will evaporate and cloud the glass. Install in reverse order of removal, noting the following: Guide low beam headlamp into headlamp housing.