Filed Under (Ford) by admin on 07-05-2011
Selector Lever Cable Vehicles Equipped with a 6R60 Transmission Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02. 3. With the selector lever in PARK, disconnect the selector lever cable from the selector lever. Vehicle equipped with a 6R60 transmission 6. Remove the cable shield by prying on the shield closest to the boot, then sliding the shield away from the boot. 4. Disconnect the selector lever cable from the selector lever housing. 7. Unlock the lock tab and disconnect the selector lever cable end from the transmission manual lever. 5. Pull the cable and grommet through the floorpan. 8. Disconnect the selector lever cable from the bracket and remove the cable. Vehicles equipped with a 5R55S transmission 9. Remove the cable shield by prying on the side of the shield closest to the boot, then sliding the shield away from the boot. 10. Unlock the lock tab and disconnect the selector lever cable end from the transmission manual lever. 11. Disconnect the selector lever cable from the bracket and remove the cable. Installation Vehicles equipped with a 6R60 transmission 1. Install the selector lever cable into the bracket. 2. Connect the selector lever cable end onto the transmission manual lever and lock the lock tab. 3. NOTE: If the shield is loose, install a new shield. Install the cable shield. Vehicles equipped with a 5R55S transmission 4. Install the selector lever cable into the bracket. 5. Connect the selector lever cable end onto the transmission manual lever.
Related entry: how to replace the hood release cable on a 2006 hyundai sonata
, replace picasso gear change cable
, mtx75 selecter
, jeep liberty 4wd lever disconnected
, ford KA transmission brake cable
, how to remove Selector mechanism (MTX75 Mk3 Gearbox)?
, how to change picasso gear change cable
, how to change gear selector cable chevrolet
, gmc envoy replace 4wd knob
, what is the b mode selector on the mirage
Filed Under (Ford) by admin on 26-11-2010
TRANSMISSION: E4OD SUBJECT: No upshift 4th gear starts, harsh upshifts, neutrals out after shifts APPLICATION: Ford-E/F Series, Bronco DATE: Jan 1995 E4OD No Upshifts, 4th Gear Starts, Harsh Upshifts, Neutrals Out After Shifts All of these concerns can be the result of an inappropriate Manual Lever Position (MLP) sensor signal. The MLP sensor consists of six resistors connected in series (ganged). The resistance of the MLP sensor will vary based on which range the transmission is in. The MLP circuit can be checked using the following steps. (Step 1) Check the MLPS ground: Turn the ignition on. The voltage on pin 46 (sensor ground ) should not exceed .1v. If the voltage is excessive, add an additional ground to the existing ground wire (figure 2). Figure 2 Splice an additional ground from the existing ground wire to a known good ground.The negative post of the battery is the best. This view is of the pins of the MLP connector pins. (Step 2) Check the MLPS voltage: The voltage at pin 30 should vary-in increments- according to the position of the manual lever (figure 3). MLP voltage (ignition on) should be within 20% of these specifications. Note It is recommended that you use a break-out box. If a break-out box is not available, you will need to pierce the wires to pins 30 and 46 for these tests.
Filed Under (Ford) by admin on 09-09-2010
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut.