Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
- with CODE (848) Electric pivoting side window Remove/Install 1 Remove paneling on C-pillar 2 Secure window against falling down. NOTE: To avoid damage to window or paintwork 3 Unscrew bolts (A) at hinges Screw for side window hinge to C pillar = 12 Nm 4 Pull back cover at opening mechanism Pull back cover at opening mechanism NOTE: For access to connecting point at opening mechanism. 5 Remove window NOTE: Caution: Do not damage window and paint if adhesive tape or support is removed Extend window toward top (B). Check seal. If necessary, replace seal of side window. 6 Install in the reverse order

download
Condition The anti-theft alarm (ATA) may sound for no apparent reason after being armed DTC P1716, indicating an interior protection/tow sensor fault may be stored in the All Activity Module (AAM) as a result. The possible cause of this condition may be a software error in the security/trip computer tow sensor. Procedure 1. Verify that this service campaign has not already been performed (see step 5) 2. Replace the security/trip computer depending on the vehicle options (see WIS: AR54.21-P-9832GH Removing and installing trip computer control module and AR82.20-P-1100GH, Removing and installing front overhead control panel). 3. Version code the AMM using StarDiagnosis (DAS) or the Hand-Held Tester (HHT) as follows: ^ 09 Trip computer ^ Set to “present” (if equipped) ^ 12 ATA Interior/anti-tow protection ^ Set to present 4. Read out and erase any relevant DTC’s using StarDiagnosis or the HHT. 5. Affix the orange sticker supplied with the replacement computer to the inside of the garage door opener access panel or Home-link(R) universal access panel. Note: The orange sticker is used to identify the vehicle as having been retrofitted with a new security/trip or security computer. Do not confuse the aforementioned orange sticker with the orange or green sticker that may already be present on the replacement security/trip computers.

download
- with CODE (U49) Styling Package Remove/Install 1 Remove cover (1) from bumper NOTE: Do not break retaining lugs. 2 Remove bulb housing (2) NOTE: To unlock, rotate counterclockwise. Installation: Ensure that the locking device has locked securely. 3 Remove fog lamp insert (6) from housing Installation wedge: See Special Tools below. 4 Disconnect connector (4) 5 Remove bulb on the back of the fog lamp insert (6) CAUTION: Do not hold the bulb with bare fingers, as fingerprints bake and leave behind opaqueness on the bulb. Use a soft, lint-free cloth. NOTE: Lock securely. 6 Install in the reverse order Special Tools

download
AR68.20-P-2020GI Remove/Install Rear Center Console – Models 163.154/174 #A as of 289565 – Models 163.157/175 (all) Remove/Install 1 Remove armrest lid (1) 2 Remove stowage box in the center console NOTE: Press the center pin approx. 4 mm downwards, then remove the rivet upwards 3 Remove screws (2) on the cup holder 4 Remove inner part of ashtray 5 Remove ashtray trim (3) CAUTION: Risk of breaking the clips (4) NOTE: Loosen clips (4) and pull back the lower edge of the cover and remove upwards 6 Remove screws (5) 7 Unclip rear center console (6) above (arrows) Long wedge: See Special Tools below. 8 Remove rear center console (6) from the center console 9 Disconnect plug from control module of rear control panel and ashtray NOTE: Disconnect plug of the rear ashtray from ashtray housing 10 Install in the reverse order Special Tools Long Wedge P/N # 115 589 03 59 00

download
CAUTION: See brake fluid notes See notes on repairs to brake system 1 Check fluid level The fluid level must be between the “MAX.” and “MIN.” marks embossed in the brake fluid expansion reservoir (10). 2 If fluid level is too low, locate and rectify the cause Check brake disks and brake pads for wear and condition. Check brake system, ABS, ETS, ASR, ESP, SBC (also pressure reservoir, charging pump and charge plunger unit in wheelhouse) for leak tightness.