Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
- with CODE (U49) Styling Package Remove/Install 1 Remove cover (1) from bumper NOTE: Do not break retaining lugs. 2 Remove bulb housing (2) NOTE: To unlock, rotate counterclockwise. Installation: Ensure that the locking device has locked securely. 3 Remove fog lamp insert (6) from housing Installation wedge: See Special Tools below. 4 Disconnect connector (4) 5 Remove bulb on the back of the fog lamp insert (6) CAUTION: Do not hold the bulb with bare fingers, as fingerprints bake and leave behind opaqueness on the bulb. Use a soft, lint-free cloth. NOTE: Lock securely. 6 Install in the reverse order Special Tools

download
Model 170 (SLK32O only), Model Year 2002 and later Engine Control Unit Software Update The Flashware CD release 0004488102/0005 (refer to S-B-07.61/30) or any newer version contains a software update for the engine control unit for the following conditions. Please use only the latest flash CD for flashing. Note: Do not flash Model 230 (SL5OO) with chassis number lower than F029500. ME software with part no. 113 153 34 79 will not communicate with transmission control unit resulting in a no start condition. Note: Emissions are not exceeded under normal conditions. All M112/M113 Engines – Model 220/215 MY 2003 and later remaining models MY 2002 and later: ^ Lack of power under full acceleration and mid range and/or upper long-term adaption values drifting to lean. ^ Hesitation caused by “two-footed” driver, i.e. driver depresses accelerator and brake pedal at the same time as outlined in DTB # 302 dated May 29, 2001. After flashing the ECU will have part number as follows:

download
Open cap with detent (2) or 2-stage cap (2a) expansion reservoir (1) or radiator. NOTE: – Cap with detent (2): Rotate cap with detent (2) carefully to first predetent, release pressure, then unscrew cap with detent (2). – Model 163: Rotate 2-stage cap (2a) or 1-stage cap half a revolution in anti-clockwise direction, release pressure, then unscrew 2-stage cap (2a) or 1-stage cap. Set heating switches to maximum heating capacity – All except Model 163 NOTE: Model 163 has no pulsed valves. Coolant is permanently flowing through the heating system heat exchanger. Inspect Check coolant level, if required adjust correctly. NOTE: In case of inadequate antifreeze content, Replace coolant against a separate job order. Fit the test cap (3) on the expansion reservoir or radiator Connect tester Apply pressure to cooling system and check leaktightness of cooling system Inspect cooling and heating hoses as well as their connection points for proper condition and loss of coolant, replace coolant hoses, if necessary. Check condition and seating of hose clamps and retighten or replace if necessary. Install in the reverse order.

download
Model 215 S110s1 Scroll forward/back button S110s3 System selection button S111s1 + and – specific function setting and volume control button S111s3 Accept/terminate phone call button General information The Active Service System (ASSYST) is operated via the reset button of the instrument cluster (A1), which is located on the left (models 203, 208 and 210) or on the right side (model 215) of the instrument cluster (A1). The individual menu items CAN-Be selected by pressing the scroll forward/back button (S110s1), as well as the system selection button (S110s3) of the multifunction steering wheel (MFL). Service indicator can be called up by driver A function requirement is that the ignition key (models 208, 210) or transmitter key (A8/1) (models 203, 215) must be in position “circuit 15R ON”, “circuit 15 ON” or driving mode must be present. The driver must observe the following procedure to display the service indicator: z Press the system selection button (S110s3) repeatedly until the basic display with the total and daily distance is shown on the multifunction display (A1p13). This step is only necessary if the basic display is not yet shown. z Press the scroll forward/back button (S110s1) until the service symbol and the current remaining distance, remaining time or service exceeded are displayed. Display engine-oil level

download
A1p13 A1s3 S110s1 Scroll forward/back button S110s3 System selection button S111s1 Buttons + and – for setting specific functions and volume control 1 Turn key in ignition switch to position “1″ 2 Press system selection button (S110s3) repeatedly until the basic display (kilometer reading or temperature display) or speed display is shown in the multifunction display (A1p13) Multifunction display Trip odometer reset button 3 Briefly press the trip odometer reset button (A1s3) 3 times ¤ An acoustic signal is heard and the voltage is shown in the multifunction display (A1p13). 4 Press lower scroll forward/back button (S110s1) ¤ The “Service Menu” appears in the multifunction display (A1p13). 5 Press buttons + and -, setting of specific functions and volume control (S111s1) repeatedly and select “Confirmation” menu item 6 Press lower system selection button (S110s3) to confirm ¤ “Confirmation” appears in the multifunction display (A1p13) and the menu item “Complete service” is highlighted. 7 Press lower system selection button (S110s3) to confirm