Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
TIMING BELT Removal 1. Disconnect negative battery cable. Remove upper engine torque strut attaching bolts and remove engine torque strut. See Fig. 5 . Remove engine torque strut bracket from strut tower. On PT Cruiser (Turbo), discharge and evacuate A/C system. Disconnect A/C lines at junction block near upper timing belt cover. 2. On all models, remove upper timing belt cover bolts and remove cover. See Fig. 6 . Raise vehicle on hoist and remove right front wheel. Remove splash shield. See Fig. 7 . Remove accessory drive belts. Remove crankshaft damper. See Fig. 8 . Remove pencil strut. See Fig. 2 . Remove lower engine torque strut. See Fig. 5 . 3. Disconnect exhaust system front pipe from manifold. Disconnect A/C pressure switch at rear of compressor housing. Lower vehicle and support engine with a jack. If not done previously, discharge and evacuate A/C system. Disconnect A/C lines at junction block. Remove screw attaching ground strap to strut bracket. Remove torque strut bracket from strut tower. Remove upper radiator closure panel. Without disconnecting lines from power steering pump, remove pump and bracket and set pump aside. 4. With engine properly supported, remove right engine mount through-bolt. See Fig. 5 . Raise engine with jack until engine support bracket bolts are accessible, and remove engine support bracket. See Fig. 9 . Remove lower timing belt cover bolts and remove cover. See Fig. 6 . CAUTION: When aligning crankshaft and camshaft timing marks, always rotate engine from crankshaft. Camshaft should not be rotated after timing belt is removed, or damage to valve components may occur. CAUTION: Crankshaft sprocket TDC mark is located on the trailing edge of sprocket tooth. Failure to align trailing edge of sprocket tooth to TDC mark on oil pump housing will cause camshaft timing marks to be misaligned. 5. Before removal of timing belt, rotate crankshaft until TDC mark on oil pump housing aligns with the TDC mark on crankshaft sprocket (trailing edge of sprocket tooth). See Fig. 10 . 6. Loosen timing belt tensioner lock bolt, and insert a 6-mm Allen wrench into hexagon opening located on top plate of belt tensioner pulley. See Fig. 11 . Rotate top plate clockwise until there is enough slack in timing belt to allow for removal. If reusing old timing belt, mark belt with arrow to indicate original direction of rotation. Remove timing belt. CAUTION: If timing belt was damaged due to incorrect rotating tracking (alignment), belt tensioner pulley and bracket must be replaced as an assembly.

download
CAUTION: The following procedure can only be used if camshaft sprockets have NOT been loosened or removed. If camshaft sprockets have been removed, special tools and timing procedure are required. 1. Disconnect negative battery cable from jumper terminal. Remove upper radiator crossmember (may also be referred to as the engine compartment support). Remove electric cooling fan module with fans. 2. Remove accessory drive belts. Hold crankshaft damper stationary while removing center bolt. See Fig. 1 . Use gear puller to remove crankshaft damper. Remove the A/C belt guide/lift bracket. 3. Remove lower timing belt cover. Remove stamped steel (right side) timing belt cover. DO NOT remove the sealer on the stamped steel cover, as it is reusable. 4. Remove cast (left side) timing belt cover. If reusing old timing belt, mark belt direction of rotation for reinstallation. CAUTION: Align camshaft sprockets between marks on rear belt covers before removing timing belt, or damage to valves and pistons may occur. CAUTION: When aligning timing marks, always rotate engine by turning crankshaft. Failure to do so will result in valve and/or piston damage. 5. Rotate crankshaft to align crankshaft sprocket timing mark with TDC mark on oil pump housing. Align camshaft sprockets with marks on rear covers. See Fig. 2 and Fig. 3 . CAUTION: When timing belt tensioner is removed from engine, always store tensioner with plunger facing up. 6. Remove timing belt tensioner. See Fig. 1 . Store with plunger facing up. Remove timing belt.

download
1. Raise vehicle on hoist and remove right front wheel. Remove right inner splash panel. Remove accessory drive belts. Remove crankshaft vibration damper. 2. Remove generator drive belt idler pulley. Remove lower timing belt cover. 3. Remove right engine support assembly vertical bolts from bottom of frame rail (timing belt end of engine). 4. Lower vehicle. Remove upper timing belt cover. Place floor jack under vehicle to support weight of engine and transaxle assembly. Remove 3 bolts attaching engine mount assembly to engine bracket. 5. Move A/C drier aside. Remove coolant reservoir tank. Remove right engine mount. Remove 3 bolts attaching engine mount bracket to engine block. CAUTION: Align timing marks by rotating crankshaft only. Do not rotate camshaft after timing belt is removed, or engine damage may result. 6. Rotate crankshaft clockwise to align timing marks on camshafts and oil pump housing. See Fig. 1 . CAUTION: Crankshaft sprocket mark must be located on trailing edge of sprocket tooth. Failure to align trailing edge of sprocket tooth with oil pump housing mark will cause camshaft marks to be misaligned. 7. On models equipped with hydraulic tensioner, remove hydraulic tensioner bolts and remove tensioner. Place hydraulic tensioner in vise, and SLOWLY compress tensioner plunger. Align the holes in the tensioner body and plunger, and insert a pin through the body and plunger to lock the plunger in place. Skip next step. 8. On models with a mechanical timing belt tensioner, insert a 6-mm Allen wrench into tensioner. Insert long end of 3-mm Allen wrench into pin hole on front of tensioner. While rotating the tensioner counterclockwise, push in lightly on the 3-mm Allen wrench until it can be pushed into locking hole. See Fig. 2 . 9. On all models, if reusing old timing belt, mark belt with arrow to indicate original direction of rotation. Remove timing belt.

download
1. Remove upper intake manifold. 2. Remove cylinder head covers, crankshaft damper, and timing chain cover. CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage. Fig. 70 3. Align crankshaft sprocket timing mark to mark on oil pump housing (Fig. 70). The mark on oil pump housing is 60° ATDC of #1 cylinder. CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage. 2000 Dodge Intrepid V6-2.7L VIN R Fig. 74 4. Remove primary timing chain tensioner from right cylinder head (Fig. 74). 5. Remove camshaft position sensor from left cylinder head (Fig. 69).

download
4. Align crankshaft sprocket timing mark to the mark on oil pump housing (Fig. 122). NOTE: Lubricate timing chain and guides with engine oil before installation. 5. Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (Fig. 122). 6. Lower the primary chain with left side sprocket through the left cylinder head opening. NOTE: The camshaft sprockets can be allowed to float on the camshaft hub during installation 1 – CAMSHAFT TIMING MARKS 2 ? CHAIN GUIDE 3 – CRANKSHAFT TIMING MARKS 4 – CRANKSHAFT SPROCKET 5 – CHAIN TENSKJNER ARM 6 – CHAIN TENSIONER 7 – CAMSHAFT TIMING MARK 8 – INTAKE CAMSHAFT SPROCKETS 9 – CHAIN GUIDES 10 – WATER PUMP SPROCKET 7. Loosely position left side camshaft sprocket over camshaft hub. 8. Align timing (plated) link tq the crankshaft sprocket timing mark (Fig. 122). 9. Position primary chain onto water pump drive sprocket. 10. Align right camshaft sprocket timing mark to the timing (plated) link on the timing chain (Fig. 122) and loosely position over camshaft hub. 11. Verify that all chain timing (plated) links are properly aligned to the timing marks on all sprockets (Fig. 122). 12. Install left side lower chain guide and tensioner arm (Fig. 120). Tighten attaching bolts to 28 Nm (250 in. lbs.). NOTE: Inspect oil ring on chain guide access plug before installing. Replace O-ring as necessary. 13. Install chain guide access plug to left side cylinder head (Fig. 120). Tighten plug to 20 Nm (15 ft lbs.)