Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Getting started 1. Apply the handbrake. 2. Place chocks under the front wheels and engage 1st gear. Remove the Brake Caliper 6. The brake caliper needs to be removed to allow the brake disc to be removed. Working under the car remove the clip securing the brake hose in place. 3. Loosen the rear wheel nuts using a 19mm wheel wrench with the car on the ground. 4. Jack up the car and support safely using axle stands or ramps. Preferably jack up both sides at the same time, as it makes it easier to balance the handbrake action at the end. This will free the hose and pipe. Carefully slip the pipe fitting out of the bracket. 7. Remove the caliper lower fixing bolt (16mm socket). 5. Remove the road wheel. 8. Remove the plastic cap over the upper fixing bolt. Remove the Brake Disc 11. Loosen the brake disc holding screw using a T-30 Torx bit. 9. Use a 6mm allan key to remove the upper fixing bolt. 12. Release the hand brake and remove the brake disc. If this proves difficult, it may be necessary loosen the brake adjuster. To do this, remove the rubber plug…. 10. The caliper will now be loose and can be carefully lifted away from the disc, taking care to route the brake pipe gently to avoid strain. Support the caliper from the suspension spring using string or ties. …and turn the adjuster with a screwdriver inserted through the hole. The disc has been removed here to show the teeth on the adjuster.

download
TROUBLE SHOOTING GUIDE (1) The display does not show the radio information. – Reset the head unit using the recessed front panel button (see user manual) – Check the uni-link plug is fitted to the rear socket of the head unit. – Check the 14pin plug is installed into the adapter. – Check the connections to the adapter and head unit. – Check that the connection to the head unit remote power has been made (Step 5) – Consult your supplying dealer. (2) The steering wheel controls do not operate the head unit. – Reset the head unit using the recessed front panel button (see user manual) – Check that the 3.5mm jack plug is fitted into the 3.5mm socket of the head unit. – Check the correct fitting of the 14pin plug to the adapter. – Check for broken or loose wiring within the supplied harness. – Consult your supplying dealer. (3) The head unit does not operate after installation. – Reset the head unit using the recessed front panel button (see user manual) – Check all connections are pushed fully into the rear terminal block on the car head unit. – Check that there are no broken pins on the lead or rear terminal. – Check the supply fuse to the head unit. – Consult your supplying dealer.

download
How to enter MENU mode on all PSA vehicles EXCEPT C2,C3 Press and hold simultaneously On C4 Vehicles use STEERING WHEEL CONTROLS as per manufacturer’s instructions. How to enter MENU mode on C2 & C3 vehicles Press and hold simultaneously 2 A D O TOOLS REQUIRED. Torx driver T8 2x Single DIN Radio Release Keys. 1 REMOVAL OF PEUGEOT 407 & C5 HEADUNIT. REMOVAL OF PEUGEOT 207, 307 & C4 HEADUNIT

download
To prevent damage, ensure steering wfieel and spiral cable DO NOT rotate before or during reassembly. SRS warning lamp Airbag Operation • Switch ignition ON. a SRS warning lamp illuminates. D Lamp extinguishes after approximately 6 seconds. • If not: Refer to Self-diagnosis section. D SRS control module fault memory can only be checked using diagnostic equipment connected to the data link connector (DLC). Disarm the system /0\ ^ ^ ^ J ^ ^ ^ / When Fascia/instrument panel removal or replacement. Front seat belt removal or replacement. Front seat repair or replacement. Repair wor1< around SRS components, especially airbag and pretensioners. • SRS component removal or replacement. D Steering wheel/column repair or replacement. • Welding operations. • • • o How n Ensure ignition switched OFF. o Remove ignition key. • Disconnect battery earth lead. Make sure accidental reconnection is not possible. • Wait 10 minutes tiefore commencing work. Arm the system : ^ How n Ensure ignition switched OFF. D Reconnect battery earth lead. D Keep clear of deployment area. D Switcti ignition ON. • Check SRS warning lamp operation.

download
Instrument panel, airbag assembly passenger disable switch, multifunction control module, transmission selector lamp, engine coolant blower motor control module F5 Air conditioning (AC), stop lamps, anti-lock brake system (ABS), engine coolant blower motor relay F6 Clock, multifunction control module, instrument panel, boot lid/tailgate lamp F7 Heated rear window Engine management, air conditioning (AC), engine coolant blower motor relay, engine coolant blower motor control module F10 Hazard warning lamps, interior lamps Light switch, hazard warning lamps, clock, instrument illumination, headlamp adjustment, audio system, air conditioning (AC), automatic transmission (AT), heated rear window, heated seat – driver’s side F12 Rear fog lamps F13 Convertible top system relay F14 Rear electric windows, heated seats F15 Trailer socket