Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
To prevent damage to the oil ?lter cap assembly, this procedure must be closely followed during oil ?lter replacement to avoid immediate and future oil ?lter serviceability concerns. The following engines are equipped with a plastic oil ?lter cap assembly: • 1UR-FE (Tundra, Sequoia) • 3UR-FE (Tundra, Sequoia, Land Cruiser) • 2ZR-FE (Corolla, Matrix) • 1AR-FE (Highlander, Venza) • 2AR-FE (RAV4, Camry) Repair Procedure NOTICE During oil ?lter replacement: • Ensure that SST 09228-06500-02 or 09228-06501 is used to remove and install the oil ?lter cap — or damage to the cap may occur. • Inspect the SST for any damage or distortion before use. • Con?rm that the SST is fully seated on the oil ?lter cap when removing/installing (see Figure 1). Figure 1. 1 3 4 1 2 3 4 • Ensure a torque wrench is used for oil ?lter cap installation. Torque: 25 +/- 5 N*m (255 +/- 51 kgf*cm, 18 +/- 3.7 ft*lbf) • There is a possibility the oil ?lter cap will be dif?cult to remove if the torque range is exceeded. FAILURE TO FOLLOW THE INSTRUCTIONS ABOVE MAY RESULT IN OIL FILTER CAP AND/OR SST DAMAGE. With Drain Plug Without Drain Plug Oil Filter Cap SST (09228-06500-02 or 09228-06501) Refer to the Technical Information System (TIS) when replacing the oil ?lter, applicable model and model year Repair Manual: • 2010 Camry: Engine/Hybrid System – Lubrication – “2AR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 / 2010 Corolla: Engine/Hybrid System – Lubrication – “2ZR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 Highlander: Engine/Hybrid System – Lubrication – “1AR-FE Lubrication: Oil and Oil Filter: Replacement” • 2008 / 2009 Land Cruiser: Engine/Hybrid System – Lubrication – “3UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 / 2010 Matrix: Engine/Hybrid System – Lubrication – “2ZR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 RAV4: Engine/Hybrid System – Lubrication – “2AR-FE Lubrication: Oil and Oil Filter: Replacement” • 2008 / 2009 / 2010 Sequoia (3UR-FE): Engine/Hybrid System – Lubrication – “3UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2010 Sequoia (1UR-FE): Engine/Hybrid System – Lubrication – “1UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2007 / 2008 / 2009 / 2010 Tundra (3UR-FE): Engine/Hybrid System – Lubrication – “3UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2010 Tundra (1UR-FE): Engine/Hybrid System – Lubrication – “1UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 Venza: Engine/Hybrid System – Lubrication – “1AR-FE Lubrication: Oil and Oil Filter: Replacement”

download
Some 2004 – 2009 model year Highlander, 2001 – 2005 model year RAV4, and 2004 – 2010 model year Sienna AWD (4WD) vehicles may display a transmission ?uid or gear oil seepage from a vent on the right side of the transfer case. The seepage is from the transfer RH (right-hand) bearing retainer No. 2 oil seal. Production improvements have been implemented to prevent this condition from occurring. Follow the repair procedure in this bulletin to replace the RH bearing retainer No. 2 oil seal assembly. Transmission Fluid or Gear Oil Seepage from Transfer Case Vent (AWD) Repair Procedure: Removal 1. Con?rm source of gear oil/transmission ?uid seepage is from vent on RH bearing retainer. 2. Remove the engine assembly with transaxle. Refer to the Technical Information System (TIS), applicable model and model year Repair Manual: • 2004 Highlander: Engine/Hybrid System – Engine Mechanical – “2AZ-FE / 3MZ-FE: Partial Engine Assy: Replacement” • 2005 Highlander: Engine/Hybrid System – Engine Mechanical – “2AZ-FE / 3MZ-FE: Partial Engine Assy: Replacement” • 2006 Highlander: Engine/Hybrid System – Engine Mechanical – “2AZ-FE / 3MZ-FE Engine Mechanical: Engine Assembly: Removal” • 2007 Highlander: Engine/Hybrid System – Engine Mechanical – “2AZ-FE / 3MZ-FE Engine Mechanical: Engine Assembly: Removal” • 2008 / 2009 Highlander: Engine/Hybrid System – Engine Mechanical – “ 2GR-FE Engine Mechanical: Engine Assembly: Removal” 3. Remove the automatic transmission w/transfer. Refer to TIS, applicable model and model year Repair Manual: • 2004 Highlander: Drivetrain – Automatic Transmission/Transaxle – “Automatic Transaxle Assy (U151E/U151F) / (U241E/U140F): Replacement” • 2005 Highlander: Drivetrain – Automatic Transmission/Transaxle – “Automatic Transaxle Assy (U151E/U151F) / (U241E/U140F): Replacement” • 2006 Highlander: Drivetrain – Automatic Transmission/Transaxle – “U140F / U151F Automatic Transaxle: Automatic Transaxle Assembly: Removal” 4. Remove the transfer case No. 1 plug and remove the gasket from the plug. 5. Remove the transfer drain plug and remove the gasket from the drain plug. 6. Remove the transfer assembly. A. Remove the 2 bolts and 6 nuts. B. Using a plastic hammer, drive out the transfer assembly from the transaxle assembly. NOTICE • Disconnect the transfer assembly from the transaxle assembly without tilting. • When moving the transfer assembly, do NOT hold the assembly by the oil seals.

download
4Runner FJ Cruiser Land Cruiser Sequoia Tacoma Tundra 1GR 2UZ 2006 2007 1GR 2006 2007 2UZ 2006 2UZ 2006 1GR 1GR 2UZ 2006 Example: 06 A P 0 00001 06: Year of Manufacture A: Month of Manufacture (A – M, “I” not used) P: Transmission Model Code (A750*) (A750 ) 0: Plant Code 00001: 5 Digit Serial Number 5–Digit Location: Right Rear on Transmission Case Above Transmission Pan (as shown below) Camry 2006 2AZ Highlander 2006 2007 3MZ RAV4 2006 2GR Example: 06 A L 0 00001 06: Year of Manufacture A: Month of Manufacture (A – M, “I” not used) L: Transmission Model Code (U15#) 0: Plant Code 00001: 5 Digit Serial Number 5–Digit Location: Slightly Off Center to the Left on Top of Bell Housing of Transmission (as shown below)

download
Models ‘04 – ‘05 Highlander, RAV4, Sienna, & Solara, ‘05 Scion tC This service bulletin provides the proper procedures for normal maintenance re- initialization of the indirect Tire Pressure Warning System (TPWS). When performing service that requires tire rotation or tire replacement, suspension component replacement or alignments, the Tire Pressure Warning System must be re-initialized. During initialization, the Tire Pressure Warning System, located within the ABS or Skid Control ECU, learns the tire sizes from rotational speeds and resonance frequencies.

download
Introduction Immobilizer Reset is a new feature that allows the registration of a new Master Key even if all original Master Keys are lost. Once the Immobilizer system is reset, all previously registered keys will be erased.Function
The Immobilizer Reset function is a 5-step process: Description 1. Using the Diagnostic Tester, retrieve a “Seed Number” through the OBD/MOBD Immobilizer function. S A “Seed Number” is a unique number provided by the Diagnostic Tester and validated by TIS in order to return a Passcode. 2. Using TIS, select Immobilizer Reset, and complete the request form to retrieve a “Passcode Number.”
S A “Passcode Number” is a unique number required by the Diagnostic Tester to reset the ECU allowing it to accept a new Master Key. 3. Enter the “Passcode Number” received from TIS into the Diagnostic Tester. 4. Confirm successful Immobilizer reset and new Master Key registration. 5. Register any additional customer keys.