Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Special Tool(s) Safety Belt Bolt Bit 501-010 (T77L-2100-A) Windshield and Molding/Trim Removal Kit or equivalent 107-R0401 Removal 1. If equipped, remove the retractable cargo cover. 2. Remove the liftgate scuff plate (13144). 1. Starting at either end and working along the liftgate scuff plate, use Windshield and Molding/Trim Removal Kit to remove the scuff plate. 2. Remove the liftgate scuff plate. 3. If equipped, remove the rear power lock switch assembly. Disconnect the electrical connector. 4. Remove the B-pillar trim panel. For additional information, refer to Trim Panel—B-Pillar. 5. Remove the three rear quarter trim panel screws. Position the carpet aside to gain access to the screws. 6. Remove the rear safety belt anchor nut. 7. Open the rear safety belt guide bolt cover. 8. Using the special tool, remove the rear safety belt guide bolt. 9. Remove the quarter trim panel (31012). 1. Remove the pin-type retainers. 2. Feed the safety belt webbing through the opening in the quarter trim panel. 3. Remove the quarter trim panel. Installation 1. Install the quarter trim panel. 1. Feed the safety belt webbing through the opening in the quarter trim panel. 2. Position the quarter trim panel. 3. Install the pin-type retainers. 2. Using the special tool, install the rear safety belt guide bolt. 3. Close the rear safety belt guide bolt cover 4. Install the rear safety belt anchor nut. 5. Install the three rear quarter trim panel screws. 6. Install the B-pillar trim panel. For additional information, refer to Trim Panel—B-Pillar. 7. Install the liftgate scuff plate. 1. Position the liftgate scuff plate. 2. Start at either end and work along the liftgate scuff plate, pushing it into the floor panel. 8. If equipped, install the retractable cargo cover.

download
Removal 1. Disconnect battery ground cable. Disconnect positive battery cable and wait one minute for the air bag diagnostic monitor (14B056) to deplete the air bag backup power supply. Refer to Section 01-20B. 2. Loosen main wiring connector bolt in engine compartment at LH side of dash panel (01610) and separate connectors. 3. Disconnect the radio-to-antenna wiring. Refer to Section 15-02. 4. Remove both RH and LH windshield side garnish mouldings (03598) . 5. Remove safety belt anchor bolts. Remove screws retaining both RH and LH front door scuff plates (13208) . Lift front door scuff plates and remove front door opening weatherstrips (20708) from body flanges. Scuff Plate, Front Door 6. Remove the RH and LH cowl side trim panels (02344) . 7. Remove the steering column. Refer to Section 11-04, Removal and Installation, Steering Column. 8. Remove one screw and A/C evaporator register duct (19B680) from under the steering column tube (3514) . 9. Loosen main wiring connector bolt at LH side of steering column opening and separate connectors. 10. Disconnect stoplight switch wiring connector and on manual transmission disconnect the clutch pedal position switch wiring connector. Wiring Connectors, Pedals

download
All Vehicles 1. Lower the rear door opening weatherstrip. 2. Remove the trim panel clips. Vehicles With Third Row Seats 3. Position the second row outer seats to the forward position. Vehicles Without Third Row Seats 4. Remove the rear seats. For additional information, REFER to SEATING . All Vehicles 5. Remove the lower safety belt anchor bolt. 6. Remove the trim panel. Pull the lower portion of the trim panel outward to release the lower tab. Pull trim panel downward to release upper tabs. Remove the trim panel. 7. To install, reverse the removal procedure. D-PILLAR TRIM PANEL Removal and Installation Vehicles with third row seat 1. Remove the third row seat cushion. For additional information, REFER to SEATING . 2. Remove the safety belt anchor bolt for the third seat strap.

download
Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section. Remove the liftgate scuff plate by pulling upward. 6. Remove the pin-type retainers and pull back the carpeting. Remove the rear floor loadspace trim panel. 7. Remove the two bolts and the loadspace trim panel by pulling upward. Remove the floor jack assembly.8. Remove the third row seat safety belt anchor bolt. 11. Remove the rear door scuff plate by pulling upward. 9. Remove the rear quarter trim panel pin-type retainer. 12. Fold the third row seat down. 13. Remove the rear quarter trim panel by pulling outward. • If equipped, disconnect the power point and power third row seat switch electrical connector at the rear. 10. Remove the second row safety belt anchor. 14. To install, reverse the removal procedure.

download
Item Part Number 666C04 611D52 613C46 — 611B64 66600/66800 W504042 W505274 — 10 W701259 11 63518 12 613A38 13 — 14 62418 15 624A08 16 613A38 17 W506542 18 613F18 19 W504042 20 62178 Description Safety belt guide cover Foam, safety belt retractor cover Safety belt retractor cover Safety belt retractor guide (part of 611B64) Safety belt retractor Backrest trim cover/foam pad Safety belt retractor cover screws (2 required) Safety belt retractor bolt Backrest support panel screws (8 required) (part of 613A38) Pin-type retainers (2 required) Attaching straps (2 required) Backrest support panel Screws, release handle (2 required) Release handle Release handle bezel Backrest frame Backrest-to-cushion bolts (2 required) Pivot bolt Screw, pivot bolt cover Pivot bolt cover