1997 Ford F-250/350/Super Duty Engine Front Cover Removal

0

Filed Under (Ford) by admin on 06-03-2011

download
Crankshaft front seal replacement is recommended whenever the engine front cover (6019) has been removed. 1. Disconnect battery ground cable (14301). Drain crankcase. 2. Drain cooling system. Refer to Section 03-03. 3. Remove drive belts (8620). Refer to Section 03-05. 4. Remove bolts attaching fan shroud (8146) to radiator (8005). 5. Remove fan blade (8600) from fan clutch (8A616) and remove fan shroud. 6. Remove fan clutch and water pump pulley (8509) from water pump (8501). 7. Disconnect upper radiator hose (8260) and lower radiator hose (8286) at engine (6007). Disconnect transmission oil cooler lines at radiator. 8. Remove upper radiator support bracket and remove radiator. 9. Remove generator pivot and attaching bolts. Remove generator (GEN) (10300) from generator mounting bracket (10153) and generator adjusting arm (10145). 10. Remove two bolts attaching generator adjusting arm to water pump and generator mounting bracket and remove generator adjusting arm. 11. Remove air pump pivot and attaching bolts. Remove secondary air injection pump (AIR pump) (9A486) from generator mounting bracket. 12. Remove four bolts attaching generator mounting bracket to cylinder head (6049), cylinder blocks (6010) and water pump, and remove generator mounting bracket. 13. Remove power steering pump pulley (3A733) from power steering pump (3A674). 14. Remove power steering lines from power steering pump. Remove four bolts attaching power steering pump to A/C compressor mounting bracket (2882) and remove power steering pump from A/C compressor mounting bracket. 15. Remove four bolts attaching A/C compressor (19703) to A/C compressor mounting bracket. Remove four bolts and one nut attaching A/C compressor mounting bracket to cylinder head and water pump. Remove A/C compressor mounting bracket from engine. 16. Remove the crankshaft pulley (6312) from the crankshaft vibration damper (6316). 17. Remove bolt and washer attaching crankshaft vibration damper. Remove crankshaft vibration damper using Crankshaft Damper Remover T58P-6316-D or Rotunda Gear and Pulley Puller 014-00293 or equivalent. Remove Woodruff key and crankshaft damper spacer from crankshaft (6303).

Related entry:

2000 blazer vapor canister mounting bracket, vapor canister blazer bracket, navistar clean feed power cable, installing front license plate bracket on 2004 ford freestar minivan, how to remove clutch fan on navigator 5 4 dohc, ford contour crankshaft pulley removal, crankshaft pulley 1996 ford contour, audi a4 fan pulley removal, 2002 cavalier brake caliper slide pin torque value, wiring ac kompresser kancil,

1999-2003 Ford F-150 SLIDING BACK GLASS WINDNOISE/WATER LEAK – SEAL REPLACEMENT

0

Filed Under (Ford) by admin on 06-01-2011

download
ISSUE: Some 1999-2003 F-150 vehicles may exhibit windnoise and/or a water leak from the back glass area. ACTION: To service, order and install Service Kit 3L3Z-1542052-AA. Refer to the installation instructions included in the kit. It will also be necessary to obtain a tube of Motorcraft Instant Adhesive (TA-19) or equivalent for this repair. NOTE: THE KIT APPLIES TO BOTH MANUAL AND POWER SLIDING REAR WINDOWS. OPERATION 040202A Install Backlight Sliding Seals (Includes Time To Remove Rear Seat Back On S/Cabs Vehicles Or To Loosen Upper Portion Of Back Panel On Regular Cab And Super Crew Vehicles

2004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD)

0

Filed Under (Chevrolet) by admin on 26-05-2010

download
Tools Required J 45859 Axle Remover Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 3. Remove the rotor. Refer to Brake Rotor Replacement – Front in Disc Brakes. Fig. 62: View Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD)