2003 Buick Park Avenue Ultra Drive Belt Replacement Removal Procedure

0

Filed Under (Buick) by admin on 22-07-2010

download
The supercharged 3800 engine uses two drive belts. The outer belt drives the supercharger. The inner belt drives the generator, power steering pump, coolant pump and air conditioning compressor. All driven accessories are rigidly mounted to the engine. Drive belt tension is maintained by the spring loaded belt tensioners. Each belt has its own tensioner. A belt squeak when the engine is started or stopped is normal and has no effect on belt durability. The drive belt tensioner can control belt tension over a broad range of belt lengths due to stretching. 1. Remove the battery. 2. Rotate the tensioner (2) counterclockwise to remove the drive belt (1). 3. Remove the supercharger belt (1) from the engine. 4. Rotate the tensioner (2) counterclockwise to remove the drive belt (1). 5. Remove the accessory belt (1) from the engine. Installation Procedure 1. Position the accessory drive belt (1) to the pulleys. 2. Rotate the tensioner (2) counterclockwise to install the drive belt (1). 3. Position the supercharger drive belt (1) to the pulleys. 4. Rotate the tensioner (2) counterclockwise to install the drive belt (1). 5. Install the battery.

Related entry:

mbz 230 compressor drive belt, how vto mount the drive belt megane 2000, 06 Kia Optima Belt Routing, Steering pump drive belt tension peugoet 407, pt cruiser fan or timing belt squeak when driving slow, how to remove water pump 1998 buick 3 8 eng tubo, how to change drive belt on a ford fusion, how do you change the serpentine belt in a 2008 ford fusion, drive belt route fiesta, beltdiagram1998buickparkavesupercharger,

2003 Buick Park Avenue Ultra Water Pump Replacement Removal Procedure

0

Filed Under (Buick) by admin on 10-07-2010

download
1. Drain the engine coolant. 2. Remove the drive belt. 3. Remove the supercharger idler pulley assembly. 4. Remove the water pump pulley bolts. 5. Remove the water pump pulley. 6. Remove the water pump mounting bolts (1, 2). 7. Remove the water pump. 8. Clean the gasket mating surfaces. Installation Procedure 1. Using a new gasket, install the water pump on the engine. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the water pump mounting bolts (1, 2). Tighten the short bolts (1) to 15 Nm (11 ft. lbs.). Tighten the long bolts (2) to 30 Nm (22 ft. lbs.). 3. Install the water pump pulley and bolts. Tighten the water pump pulley bolts to 13 Nm (115 inch lbs.). 4. Install the supercharger idler pulley assembly. 5. Install the drive belt. 6. Fill the cooling system.

2003 Buick Park Avenue Ultra Drive Belt Idler Pulley Replacement (Lower) Removal Procedure

0

Filed Under (Buick) by admin on 05-07-2010

download
1. Remove the supercharger drive belt. 2. Remove the drive belt idler pulley bolt. 3. Remove the drive belt idler pulley. Installation Procedure 1. Install the drive belt idler pulley. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the drive belt idler pulley bolt. Tighten the drive belt idler pulley bolt to 50 Nm (37 ft. lbs.). 3. Install the supercharger drive belt. Drive Belt Idler Pulley – Lower Drive Belt Idler Pulley Replacement (Lower) Removal Procedure

Related entry:

2003 buick park avenue ultra idler pulley, 2003 buick 3 8 turbo engine tensioner pulley replacement youtube, 97 park avenue supercharger pulley, how to replace super charger pully buick park ave, remove idler on buick ultra with supercharger, removing idler pully assemly 2000 pontiac gm 3800,

Installation Instructions for TRD’s 3.4-liter V6 Supercharger Kit 1997-2000 Tacoma,1997-1998 T-100, 1996-2000 4Runner

0

Filed Under (Toyota) by admin on 05-04-2010

download
Removal of Stock Intake Manifold (figure 1)
1. Disconnect the battery ground cable. 2. With tape or a permanent marker, mark the forward edge of the power steering and the air conditioning compressor drive belts (figure 2). This will ensure that the belts will be returned to their original positions and that they will rotate in the direction. If you reverse the direction of rotation, it may cause the belts to fray.
3. If you don’t have a drive belt tensionometer, make note of each belt’s deflection at a point midway between its pulleys. You will need to approximate this tension during reassembly (see figure 29

Related entry:

how much R-134a to fill 2000 chevrolet tahoe, 1997 c240 user manual, service manual for 1997 chevy c2500, replace 2000 tacoma air conditioner fluid, repair mondeo 1997, google toyota 4runner 1997 3 4 electrical charging diagram, diagnostic cable for 1997 ford courier, 2000 tahoe refrigerant leaked out compressor diagnose, 2000 cirrus 2 5 litre, 1997 ford mondeo mark 2 service manual,