Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
Remove the negative battery cable. Remove the intake manifold sight shield-four nuts. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Procedure in Powertrain Management. Remove the air intake duct from the throttle body. Remove the transaxle vent hose and transaxle shift cable at the bracket. Remove the TP sensor and IAC valve connectors. Remove the accelerator cable and cruise control cable at the throttle body. Remove the front bank spark plug wires and lay them aside. Remove the throttle body coolant hoses at the throttle body and the surge tank pipe. Refer to Throttle Body Coolant Hose Replacement in Cooling System. 10. Remove the EGR pipe and the crankcase ventilation pipe at the throttle body spacer. 11. Remove the brake booster vacuum hose at the intake manifold vacuum fitting. 12. Remove the fuel rail ground wire at the rear cylinder head. 13. Remove the quick-connect fittings at the fuel rail. 13.1. Grasp both sides of the fitting. 13.2. Twist the female connector 1/4 turn in each direction to loosen any dirt within fitting. 1. 2. 3. 4. 5. 6. 7. 8. 9. Caution: Safety glasses must be worn when using compressed air, as flying dirt particles may cause eye injury. Blow the dirt out of the fitting using compressed air. Choose the correct tool from the J 37088-A for the size of the fitting. Insert the tool into the female connector, then push/pull inward to release the locking tabs. 13.5. Pull the connection apart. – Using a clean shop towel, wipe off the male pipe end. – Inspect both ends of the fitting for dirt and burrs. – Clean or replace the components or assemblies as required 14. Disconnect the fuel rail bracket at the EGR valve. 15. Disconnect the PCV hose at the intake manifold. 16. Disconnect the injector harness main connector. 13.3. 13.4.

download
Installation Instructions Part Number 200-630 2008-09 Buick Enclave 2008-09 Chevrolet Equinox Sp. 2008-09 Chevrolet Malibu 2008-09 Chevrolet Traverse 2008-09 GMC Acadia 2008-09 Pontiac G6 GXP 2008-09 Pontiac G8 2008-09 Pontiac Torrent GXP 2008-09 Saturn Outlook 2008-09 Saturn Vue XR 2008-09 Suzuki LX7 3.6L V-6 2. Disconnect the breather hose elbow from the intake tube. Loosen the two hose clamps that secure the intake tube to the throttlebody, and the mass air flow sensor. Remove the air intake tube. 1. Disconnect the negative battery cable! Remove the oil fill cap and set it aside. Lift straight up on the engine beauty cover and set it aside. Reinstall the oil fill cap after the beauty cover has been re- moved to prevent any foreign material from entering the crank- case. 3. Remove the four bolts that secure the throttlebody to the in- take manifold. 5. Install the provided bolts and washers thru the throttlebody and Poweraid Spacer and tighten to the manufacturer’s specifi- cations. 4. Install the Poweraid Spacer between the throttlebody and the intake manifold with the first supplied gasket next to the intake manifold, and the second supplied gasket next to the throttle- body as shown. Make sure the “flow” arrow printed on the spacer is pointing towards the intake manifold. 6. Reinstall the intake tube, tighten the two hose clamps, and reconnect the crankcase breather tube. Reinstall the beauty cover, and oil cap in the reverse order that they were removed. Re-connect the negative battery cable!

download
Parts List (1) Power Plate (2) Gaskets (1) Linkage Plate (4) 6mm x 50mm Bolts (4) 6mm Flat Washers (1) 6mm x 12mm Flat Head Screw (1) 6mm x 20mm Flat Head Screw (2) 6mm Nuts (1) 6mm x 40mm Bolt (1) 6mm Lock Washer (1) 5/8” Dia. X 7/8” W/ 1/4” Hole Throttle Linkage Spacer 1. DISCONNECT NEGATIVE (-) BATTERY CABLE. 2. Remove air intake assembly. 3. Remove (1) 6mm bolt from throttle linkage bracket and save. (Ref. D) 4. Remove (4) 6mm bolts from throttle body. (Ref. C) 5. Install the power plate using (2) gaskets. (Ref. A) A. Place one gasket between the throttle body and power plate. B. Place second gasket between the power plate and intake manifold. 6. Install (4) 6mm x 50mm bolts and (4) 6mm flat washers. Refer to (Ref. C) 7. Install throttle linkage bracket using (1) 6mm flat head screw and (1) 6mm flat head screw with (1) 6mm nut. 8. Attach throttle cable assembly fitting with saved 6mm bolt. Refer to Step 3 9. Install throttle linkage spacer using (1) 6mm x 40mm bolt, (1) 6mm nut, and (1) 6mm lock washer. (Ref. D) 10. Inspect & Test throttle linkage for full open & closed travel before driving. Some cruise or kickdown cables may require adjustment. Please refer to your vehicles service manual for proper adjustment. 11. Reinstall air cleaner assembly. Refer to Step 2 12. Reconnect battery cable. Enjoy!