Filed Under (Toyota) by admin on 17-08-2010
download
DTC P1780 Park/Neutral Position Switch Malfunction CIRCUIT DESCRIPTION The park/neutral position switch detects the shift lever position and sends signals to the ECM. The ECM receives signals (NSW, R, 2 and L) from the park/neutral position switch. When the signal is not sent to the ECM from the park/neutral position switch, the ECM judges that the shift lever is in D position. DETECTING CONDITION WIRING DIAGRAM 1996 Toyota Truck Landcruiser 4WD L6-4.5L (1FZ-FE)
Filed Under (Toyota) by admin on 05-06-2010
download
1. REMOVE THESE PARTS: a. Lower finish panel b. Glove compartment door c. No.2 Lower finish panel 2. REMOVE CENTER CLUSTER FINISH PANEL a. Remove the A/C switch. b. Pull out the hater control knobs. c. Remove heater control name plate. d. Remove the 2 screws. e. Using a screwdriver, release the 4 fitting clips and pull out the panel, then disconnect the connector. HINT: Tape the screwdriver tip before use. 3. DISCONNECT HATER CONTROL CABLES HINT: After connection, adjust the control cables. 4. REMOVE HEATER CONTROL ASSEMBLY Remove the 2 screws and pull out the heater control assembly, then disconnect the connector. INSTALLATION Installation is in the reverse order of removal. HINT: After installation, adjust the heater control cables.
Filed Under (Toyota) by admin on 15-05-2010
download
1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM HINT: Evacuate air from refrigeration system. Charge system with refrigerant and inspect for leakage of refrigerant. Specified amount: w/o Rear A/C: 900 ±50g (31.74 ±1.76oz.) w/Rear A/C 1,150 ±50g (40.56 ±1.76oz.) 2. DRAIN ENGINE COOLANT HINT: It is not necessary to drain out all the coolant. 3. DISCONNECT WATER HOSE FROM HEATER RADIATOR PIPES HINT: Push the water hose onto the heater radiator pipe as far as ridge on the pipe and install the hose clip.
Install the hose clip in a position. 4. DISCONNECT LIQUID AND SUCTION TUBES Remove the 2 bolts and the both tubes.
Filed Under (Toyota) by admin on 21-04-2010
Tags: air conditioning unit,
case service,
engine coolant,
heating and air,
heating and air conditioning,
hose clip,
radiator,
refrigerant,
refrigeration system,
Toyota,
toyota truck,
water hose
download
AIR CONDITIONING UNIT REMOVAL DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM HINT: Evacuate air from refrigeration system. Charge system with refrigerant and inspect for leakage of refrigerant. Specified amount: w/o Rear A/C: 900 ?50g (31.74 ?1.76oz.) w/Rear A/C 1,150 ?50g (40.56 ?1.76oz.) 1. DRAIN ENGINE COOLANT HINT: It is not necessary to drain out all the coolant.
2. DISCONNECT WATER HOSE FROM HEATER RADIATOR PIPES HINT: 3. Push the water hose onto the heater radiator pipe as far as ridge on the pipe and install the hose clip. Install the hose clip in a position. DISCONNECT LIQUID AND SUCTION TUBES 4. Remove the 2 bolts and the both tubes. Torque: 10 Nm (100 kgf-cm, 7 ft. lb.)
Filed Under (Toyota) by admin on 21-04-2010
download
IGNITION TIMING: Tachometer Hookup Start engine and allow to reach normal operating temperature.
1.Connect a tachometer test probe to terminal IG of the check connector, Fig. 211 2.NOTE: Never let the tachometer lead touch ground as this could cause damage to the igniter and/or coil. Be sure to check that your tachometer is compatible with this ignition system. Consult the operating manual for your instrument. Service Check Connector
