Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
hinges at the top of the mirror. Carefully pull at the bottom of the mirror until it unsnaps from the mirror mount. Tilt and lift the mirror out of the mirror housing. of the mirror. The heater wires are interchangeable. the bottom of the mirror sail. Separate the mirror housing from the mirror sail. 5 Unwrap the tape at the end of the mirror wire harness (seals it to the rubber sail gasket). This is required because the Signal® mirror wire will run through the rubber sail gasket in the same location. Pull away the rubber gasket from around the mirror sail. Remove the white plastic strain relief tab. Using the shorter of the two wire harnesses from the kit and starting from the inside of the mirror housing, route the wire through the mirror housing. You may need to use gopher wire to route the wire. Mirror Replacement Continued 8 9 Following along the existing factory wire, route the new wire through the mirror sail. Leave about 4 inches of wire in the mirror housing. Assemble the mirror housing and mirror. Replace the rubber gasket on the mirror sail. Remove any slack in the wire. Replace the strain relief tab. Connect the Signal® mirror mating connector to the Signal® mirror wire harness. If heated, connect the factory heater wires to the heater terminals on the Signal® mirror. NOTE: There is no polarity so the wires may be interchanged. 10 11 Tuck the wire harness behind the Signal® mirror. Align the hinges in the top of the mirror mount. Tilt the Signal® mirror down on the mirror mount. Press down on the bottom of the Signal® mirror until it snaps into position. Press down on all sides of the Signal® mirror to ensure proper operation.

download
SUBJECT: MODELS: Heated Windshield Washer Module Short Circuit – Add Wire Harness 2006-2008 model year Buick Lucerne; Cadillac DTS; HUMMER H2 vehicles; 2007- 2008 model year Cadillac Escalade, Escalade ESV, Escalade EXT; Chevrolet Avalanche, Silverado, Suburban, Tahoe; GMC Acadia, Sierra, Yukon, Yukon XL; Saturn OUTLOOK vehicles; and 2008 model year Buick Enclave vehicles equipped with a heated washer fluid system. A short circuit on the printed circuit board for the washer fluid heater may overheat the control-circuit ground wire. This may cause other electrical malfunctions, create an odor, or cause smoke. In rare cases, it may cause a fire. PARTS INFORMATION No parts are required to pull the heated windshield washer fuse. When wire harnesses are available for ordering, a revised bulletin with ordering information will be sent to dealers/retailers. SERVICE PROCEDURE Important: Until wire harnesses become available, the following procedure allows dealers/retailers to remove the heated windshield wiper fuse, disabling the system. 2007-2008 Cadillac Escalade, Escalade EXT, Escalade ESV, 2007-2008 Chevrolet Avalanche, Silverado (GMT900), Suburban, Tahoe, 2007-2008 GMC Sierra (GMT900), Yukon and Yukon XL 1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in SI. Important: The underhood fuse block is located in the engine compartment on the driver side of the vehicle. Refer to Underhood Fuse Block in the Owner’s Manual for fuse information. 2. Locate the underhood bussed electrical center (UBEC). 3. Remove the UBEC cover and locate the 60 amp heated windshield washer fuse. Important: Remove the two relays (1) next to the fuse to gain access to the fuse. 4. Remove the 60 amp heated windshield washer fuse (2) using needle-nose pliers. 5. Store the 60 amp heated windshield washer fuse in the glove compartment. 6. Install the two relays (1) removed in Step 4. 7. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in SI. 8. Test the operation of the windshield wiper system. 8.1 Ensure the wiper system functions in low and high positions. 8.2 Verify that the windshield wiper/washer switch functions. The windshield wiper system should provide wiper fluid to the windshield. 8.3 Ensure that the heated windshield washer fluid system has been disabled. • Verify that the heated windshield washer switch does NOT flash. 9. Secure the UBEC cover on the UBEC. 10. Close the hood.

download
SRS wire harnesses are routed near the steering column and passenger’s side dashboard. CAUTION: All SRS wiring harnesses are covered with yellow outer insulation. Before disconnecting any part of the SRS wire harness, install the short connectors. Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring. STEREO RADIO/CASSETTE REPLACEMENT NOTE (L and LS models): These versions have a stereo radio/cassette player with a 5-digit coded theft protection circuit. Be sure to get the code number before: -disconnecting the battery. removing the No. 56 (7.5 A) fuse. removing the radio. After reconnecting power and turning the radio ON, the word “CODE” will be displayed. Then enter the code. 1. Remove the center console panel.